control holder 3d models

It is a variation of this thing Filament spool holder (Credits: https://www.thingiverse.com/thing:2047554) I used the credited thing for one half and the custom half to mount it to the 2020 frame. Here you can find the complete model in Fusion 360:...

Remove the paper from the other side, and firmly press the part against the interior wall of the plastic box in the marked locations, making sure that for the brackets, the U shaped rod holder is facing up, and for the passthroughs, that each is...

I Recommend Hex Head screws for the enclosure and drywall screws for the hanging spool holders. 2x or more Ikea LACK tables. (I used 4 for extra storage)<br/> 2x 3M screws 15 mm long<br/> 2x 3M nuts (to replace the PSU with a printed brace)<br/> ...

There weren't enough space in the original Hercules carriage for a dial indicator holder so I decided to make this separate carriage for a dial indicator.The Hercules carriage is very easy to remove. Just unscrew the parts cooling fan duct from below...

This is where I remounted the stock spool holder, though beware it needs to be under 85mm in length which fits pretty much all 1kg spools for the bed to clear it at around 350mm on the Z axis. You will need to drill holes for wiring to be run into...

## For use with Smart Filament Sensor - Adapter for HallON v3.stl - Bracket for HallOn v3 stop and Smart Filament Sensor.stl - Stop for HallON v3.stl ## For use without Smart Filament Sensor - Adapter for HallON v3.stl - Bracket for HallOn v3...

(if you want to go faster tune the speed up to 130%)All the stls are in the right orientation.The back plate can be laser cutted or 3d printed, all the files are included.Prints the following parts:1x PanelMeterClock_v1_Body: Prusament PETG, Preset...

That was one of the first mods I did, right after the rear spool holder. My printer is getting old now and the carriage that the cartridge slides into is getting kind of worn and sloppy. It just doesn’t hold the cartridge nice n tight like it used...

I used (4) 3mm heat inserted knurled nuts into the holes at the top of the 2 side plates (Ai3M X Axis CarriageLeft and Ai3M X Axis CarriageRight). Insert the (2) X rod lenear bearings into the Ai3M X Carriage. Screw the CarriageLeft and Carriage...

I have shortened the magic band reader holder post to be more to scale with the rest. I as well added a half inch hole through the post and the plug to be able to past wires between the electronics without drilling, half inch might be oversized but...

Then just put 3D printed motor gear on motor shaft and attach the whole motor assembly to the motor holder in uicm-stator part with two small zip ties. After that, just put in two uicm-rotor parts so the gears link with motor gear and fix them with 4...

Printing the rollers sideways in halves could be a possible solution for increasing the strength of the thin spindle. The Tray: (Optional) Print the desiccant pack holder, “Drybox Desiccant Tray.stl” (Recommended line width, 0.5mm). You could also...

Take what's theirs and make it your own! ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1...

Glue is not needed on the outside of the Dupont holder. General: There are quite a few M3 inserts used in this project, and they should be heat set, but I glued them in on my kits. I decided to glue them in using clear Gorilla Glue since I have no...

(it is already in the settings in the .3mf files)Assembly:Print all three parts (hull, treads, and gun.)Superglue the treads to the hull.Place the gun on the roof.Superglue works best for gluing it together.It will scale easily if you want a larger...

- https://www.printables.com/model/855331-megalopolis-dice-tower-with-a-story Electronics:Voltage Sensor Box - https://www.printables.com/model/784371-voltage-sensor-box Voltage Sensor Box - SMALL...

Avoid lifting and warped prints!Print all three parts (body, treads, roof option.)Superglue the treads to the body.Choose the roof option and glue, or leave it free and swap it out as needed!Superglue works best for gluing it together.It will scale...

Take what's theirs and make it your own! ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1...

Take what's theirs and make it your own! ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1...

It can hang off the plywood deck (¾ inch") or the slightly thinner shelving above.&nbsp;Support enforcers are neededNo gluingEasy to printDesigned on...

Take what's theirs and make it your own! ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1...

As they came to that realization however, a druid put a mind control spell upon Gweld which made him violently attack Geralt, forcing Geralt to kill his friend with a sword through the chest. Right after this, soldiers under Radowit's command...

The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.This model was tested with PLA material.To avoid printing problems, we recommend the following settings:ExtruderNozzle Diameter: 0.4 mmExtrusion...

The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.This model was tested with PLA material.To avoid printing problems, we recommend the following settings:ExtruderNozzle Diameter: 0.4 mmExtrusion...

For small/thin parts you need to decrease the Speed by 25% - 50%.Print Speed: 50 mm/s    Infill Speed: 50 mm/s    Wall Speed: 25 mm/s          Outer Wall Speed:25 mm/s          Inner Wall Speed: 50 mm/sTop/Bottom Speed: 25mm/sSupport Speed: 25 mm/s  ...

For small/thin parts you need to decrease the Speed by 25% - 50%.Print Speed: 50 mm/s    Infill Speed: 50 mm/s    Wall Speed: 25 mm/s          Outer Wall Speed:25 mm/s          Inner Wall Speed: 50 mm/sTop/Bottom Speed: 25mm/sSupport Speed: 25 mm/s  ...

The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.This model was tested with PLA material.To avoid printing problems, we recommend the following settings:ExtruderNozzle Diameter: 0.4 mmExtrusion...

The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.This model was tested with PLA material.To avoid printing problems, we recommend the following settings:ExtruderNozzle Diameter: 0.4 mmExtrusion...

My special thanks on this and previous projects to Arthur Braune, who has been instrumental in testing and quality control on these models. Included Ships -------------- Note several ships from the Federation Reference Series have been...

The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.This model was tested with PLA material.To avoid printing problems, we recommend the following settings:ExtruderNozzle Diameter: 0.4 mmExtrusion...