concept 2 rower tablet mount 3d models

The mount can be placed on any side of the cardboard tablet with a snap. Для заметок в планшетке использую карандаш. Для его хранения нарисовал такую модель. теперь грифель карандаша под защитой. Карандаш крепко держится. ...Крепление можно размещать...

This mount positions the camera directly above the print bed on my Eustathios printer, enabling me to use both the tablet and camera for slicing and remote print monitoring. ...Check out my Google Plus post featuring a video of it in action:...

for up to a 10mm thick tablet

made and designed a tablet holder that sits on the back of my hotas for gameglass in star citizen. ... Edit: October 15th 2020 For best results: Infill 20-25% Cura Tree supports (touching base plate) .2 resolution

Mount for attaching a phone or tablet to a RigidBot. This allows you to easily use an old phone as a webcam, time lapse recorder etc. Made to allow most size phones, and even tablets - no height or width restriction. Prepared with a lip to allow...

I had my 8" Samsung tablet in the mount and it locked itself into place. ...Even after 2 hours of thrashing around Bathurst in the Ford V8 supercar, my actual wheel needs to be bigger to see the full screen, but I get the information I need, and the...

I needed a way to mount a 10 inch tablet on a window in my lab. I had a Gopro Suction cup available and all I needed was a mount.This version has the Gopro receptacle straight down. ...I have another one with a 90 degrees rotated receptacle both to the...

Tablet mount for 20 x 20 extrusion, easy mount clip on clip off, left and right versions remix of https://www.thingiverse.com/thing:2537713 Print Settings Rafts: No Supports: NoResolution: 200 Infill: 20 Filament: SUNLU PLA Category: 3D Printer...

The top part of the mount is designed to put a good amount of tension on the sides of the tablet, so there will be a second part I'll upload soon for tablets with a wider profile. Also, if you have a tablet with a charging port on the bottom and the...

This wall mount was made for Samsung 10.1" Tablets. ...Other models may work too. As my printer was too small, I made 2 parts with a groove to glue it after it is printed. You will need a M6 screw, M6 nut and some washers to put it together. Print...

This is a very strong and sturdy wall mounted articulating arm for large and heavy tablets. The holder is made for the Samsung Galaxy Note 10.1, which I use in my workshop, but can easily be customized for any other tablet on the market. I've...

Had an old Android tablet laying around not doing anything useful, decided to use it on my Ender 3 for control. Didn't find any suitable mounts, so I remixed one from some existing models. You might need to print it at 99 % or 98 %, since it slots...

Created a custom mount for tablets using 3030 extrusions. Successfully tested on various devices, including the iPad 9.7" from 2018, Samsung Galaxy Tab 4, and Samsung Galaxy Tab E. ...Additional models are expected to be compatible with this design as...

Tablet or convertible laptop mount for IKEA Skadis pegboard. Two-part model, glue with common cyanoacrylate glue. May need filing before gluing. The inserts will need a light filing or be smoothed with a lighter. Originally designed for DELL...

... Google Nest Hub under cabinet twist mount. ... They get all of the credit for the hard part of this design. What I have done is extend the pivot "tube" a bit and completely redesign the speaker base to fit the Google Pixel Tablet speaker. ...

balljoint for mounting the phone/tablet holder on the back of the arm instead, this balances the controller and brings the screen closer to you. ... I printed int CPA and 60% infill you need a short m3 screw and nut to lock the holder in place.

- 20mm plastic electric pipe - Bottom tablet stand, the groove is a bit wide, I use a bit of blue-tack to stop the tablet from sliding around. The bottom stand rests on the top of the monitor. - Adjustable top tablet holder, to let you set the...

- An adjustable top tablet holder, allowing you to set the angle of the tablet using an M4 nut, washer, and 20mm screw. It should be relatively simple to attach anything lightweight to the pipe. ... Designed in OnShape:...

Here's what you'll need: 6mm Aluminum Tube (1mm wall thickness) 2 x M3 x 10 set screws with a pointed tip (actually any M3 set screw will do) 1 x M3 x 10mm countersunk screw 1 x star washer to hold the screw 1 x M3 wing nut (I used some kind of M3...

Designed to fit most size phones and even tablets, there are no height or width restrictions on this mount. A lip has been added to accommodate LED strips, which also light up the RigidBot Community logo nicely. The design makes a good fit otherwise...

Mount for attaching a phone or tablet to RigidBot easily with old phones functioning as webcams or time lapse recorders. Designed to fit most size phones and tablets, no restrictions on height or width apply. The mount features a lip allowing LED...

... your Nexus 7 to rest comfortably. You may need to sand down the alignment notches based on your printer's precision. Feel free to customize the dimensions of part 2 to fit other tablets. ...Don't worry about messy geometry - just enjoy the upgrade!

This thing was designed so I could place my tablet in it and still use it at my desk. ...I have done a test print and fount that the upper supports were only one wall thick so I enlarged it to 2 or 3 walls thick.

Parrot SkyController 2 Strap and Tablet, Use an M4 screw without a head and insert it into the "molette".

Ipad/ tablet stand ,2 positions NB : 60% scale for the ipad mini (no cover) would have worked.

... 6 x M3 counter sunk machine screws. 6mm long including the head. Please note that the mount has been designed for the pole adapter to still have the adehisive backing unused. ...As it uses this as a spring to make the fitting nice and snug.

To accommodate a larger tablet, simply flip up the upper mounting bracket. This design is compatible with standard GoPro mounts, allowing users to utilize their existing accessories. I've successfully printed this prototype using Fused Deposition...

Wall mount hook for Amazon Fire 10.1 tablet with Tuatara case securely attaches the device using the kickstand loop of the case, eliminating the need for separate fasteners or adhesive strips. Countersunk screw holes ensure a flush finish and prevent...

This is a mount/stand for a Nexus 7 (2012) or any other phone/tablet of similar size. It simply clamps onto any Makers Rail or aluminum extrusion from 2020 makers. The object was printed vertically with support for the back brace. All visible text...

Wall mounted holder for a graphics tablet and pen case. I specifically designed this for an XP Pen Deco 03 but should fit any graphics tablet 12mm or less in thickness. The pen holder part is 35mm in diameter but has a clamp to keep smaller cases...