colonel wasp firefly 3d models

I designed a Colonel Wasp Firefly shell that is getting the same velocity (200ish FPS) as the molded shells. This also has the ability to rear load the dart. I have found it best to push the dart about 1/4 of an inch or 6ish mm from the bottom of the...

X15 shells saddle for the colonel wasp firefly. ... Parts required: 4x 2mmx10mm pins 6x M3x10mm flat head screws 2x M3x8mm flat head screws 1x M3x35mm socket head screw 3x m3 square nuts 6x m3 hex nuts

Edit 14.5.2021: Added a short version, so people with the lower capacity Firefly can use the grip aswell :) This is a Pumpgrip for Colonel Wasp awesome Firefly! The stock pumpgrip is really not the best though, even when used with a weaker spring.

This is a shell box for the colonel wasp firefly just for storage. ...Hope you liked it ;)

A single piece copy of the stock mag follower for Colonel Wasp's Firefly shotgun I've included the OpenSCAD file you so you easily edit it too.

This is a copy of the shell extractor claw of Colonel Wasp's Firefly shotgun. Overview video: https://youtu.be/SHZGhNnebOM I've included the OpenSCAD file you so you easily edit it too. ... //---------------------------- // 08/June/2020 // ...

This is a copy of the shell extractor claw of Colonel Wasp's Firefly shotgun. Overview video:https://youtu.be/SHZGhNnebOM I've included the OpenSCAD file you so you easily edit it too. ... //---------------------------- // 08/June/2020 // Initial...

This is a kit to increase your Colonel Wasp's Firefly shotgun magazine capacity from 6 upto 9! By removing the deadspace from the shells to reduce their length, using my improved mag follower (https://www.thingiverse.com/thing:4392093) and my...

This is a kit to increase your Colonel Wasp's Firefly shotgun magazine capacity from 6 upto 9! By removing the deadspace from the shells to reduce their length, using my improved mag follower (https://www.thingiverse.com/thing:4392093) and my...

This is a copy of the shell for Colonal Wasp's Firefly shotgun. ... Overview video:https://youtu.be/SHZGhNnebOM

This is a copy of the shell for Colonal Wasp's Firefly shotgun. ... Overview video: https://youtu.be/SHZGhNnebOM

Upgrade parts for the Firefly by Colonel Wasp. The pump grip provides more surfaces to push back on and increased texturing for additional hand traction. Installs using the original screws. The muzzle features a hole in the front sight post...

Monkee Mods / Colonel Wasp firefly Barrel extension Bearing make your dart more more accurate. ... need: MF63ZZ bearing * 12 M3x8.0mm - ThreadedRod * 12

This is a copy of the shell lifter of Colonal Wasp's Firefly shotgun. Overview video:https://youtu.be/SHZGhNnebOM I've included the OpenSCAD file you so you easily edit it too. ... //---------------------------- // 05/April/2021 // Initial version...

This is a copy of the shell lifter of Colonal Wasp's Firefly shotgun. Overview video: https://youtu.be/SHZGhNnebOM I've included the OpenSCAD file you so you easily edit it too. ... //---------------------------- // 05/April/2021 // Initial...

colonel wasp fire fly magazine suit included magazine well and magazine. ... video :https://www.acfun.cn/v/ac32827060 https://www.acfun.cn/v/ac32693557 spring list: magazine_release: Wire diameter:0.5mm Circle diameter:5.5mm ...

This is a copy of the swinging shell gate of Colonal Wasp's Firefly shotgun. Designed in two parts as it'd be a load of supports to print as one piece and allows for a smooth side on the side of the gate touching the shell. Print both pieces...

A stock version of my other Col Wasp's Firefly shotgun muzzle. Unprinted in this variant but base is the same as the other version which has been printed I've included the OpenSCAD file you so you easily edit it too. Just face it down to print...

This is a copy of the central holder section of Colonal Wasp's Firefly shotgun, as mine snapped. Should be compatible with the stock mag follower but I recommend my improved mag follower. https://www.thingiverse.com/thing:4392093 There are...

fishbone for firefly need: 2 M3x12-Screw 2 M3-Nut

fishbone for firefly need: 2 M3x12-Screw 2 M3-Nut new update will upload on:https://www.thingiverse.com/thing:5203880

... tube? ...epoxy this in to your mag tube holder and it'll keep your wasp from ever breaking again. Mine is made out of MJF Nylon, however PLA should suffice just fine. ...very little sanding may be needed to ensure proper fit, but that is all up to you

Doesn't the trigger hurt your finger every time when you pull the trigger of your beloved firefly? This is a small mod for thickening the trigger, so that it won't hurt your finger anymore. Print guide Print vertically on the bed, apply brim if...

Doesn't the trigger hurt your finger every time when you pull the trigger of your beloved firefly? This is a small mod for thickening the trigger, so that it won't hurt your finger anymore. --------------- Print guide --------------- Print...

A quad shell holder for the Colonel Wasp Firefly for mounting on PALS/Molle. This design is remixed from Ansuzalgiz's match saver for the shell holders and uses the PALS attachment point from Derikksun's Talon mag holder. ... I have also included a...

A new muzzle front end piece for the Colonel Wasp Firefly shotgun with a Nerf barrel attachment base. I've included the OpenSCAD file you so you easily edit it too. You will need supports from the model to support the flats of the locking...

A single piece improved version of the mag follower for Colonel Wasp's Firefly shotgun. Has a better looking non-stepped design and a slight taper to the base to help it move. I've included the OpenSCAD file you so you easily edit it too. ... 80...

These are twist fit mag caps for the colonel wasp firefly to easily change the amount of shells you can hold in the tube. Designed to be used with the short shell mod designed by Blue icarian wings https://www.thingiverse.com/thing:4964955 ...

Print the part labeled "Tab" with brim. This is a straight replacement for the shell stopper part. You will need glue to connect the two parts together, make sure you line them up straight. ...(I used CA glue)

The plunger head for my Firefly broke... not too surprising looking at reviews. This plunger will last however. This requires a threaded rod, two nuts, and craft foam sheet. These exact parts can be found at Ace Hardware with the item numbers...