collapsing bo staff 3d models

Collapsing Bo Staff These Bo Staffs collapse back into the handle similar to my other collapsing swords. There are two sizes; small and large.</p> <p>You will need 150mm of Z for the small and 205mm of Z for the large. The small staff’s handle is...

Collapsing Bo Staffs collapse back into their handles, similar to collapsing swords I've designed before. These staffs come in two sizes: small and large. For the small one, you'll need 150mm of Z material, while the large one requires 205mm of Z...

Create your own illuminated bo staff for bojutsu or festivals fun! Get complete instructions on my blog here. Utilize translucent PVC and 3/4" PVC pipe with printed files to construct this unique staff. Overwhelmed by the attention at Electric...

... ...It had been sitting on my desk and I wanted to move it somewhere out of the way. I thought it could be cool to hang it on the wall so here it is. Collapsible Bo-Staff (3Dprintingworld) https://www.thingiverse.com/thing:4251413 (Really cool design)

Reproduction Bo Staff for Thundercats Cheetara figure.

A collapsing Penguin/peep staff. ... No supports needed.

A collapsing Penguin/peep staff. ... No supports needed.

This fix the problem of the collapsible staff part not inside in Owlbert. Does fix collapsible staff poking out the the bottom. Owlbert (fix) is more snug. ... Owlbert (fix 2) is more loose.

Inspired by The Owl House this collapsing staff features a Hammerhead shark. ... Fully extended the staff is about 60cm Also included is a dowel version that uses a 7/8 inch dowel.

Inspired by The Owl House this collapsing staff features a Hammerhead shark. Fully extended the staff is about 60cm Also included is a dowel version that uses a 7/8 inch dowel. ...

This is a collapsing staff inspired by a squid. ... I used supports on build plate only to support the end of the tentacles.

This is a collapsing staff inspired by a squid. ... I used supports on build plate only to support the end of the tentacles.

A collapsing staff created by FuzedCrafts as part of her princess series of staffs&nbsp;All collapsing staff are roughly 44 inches or about 112 cm long fully extended but that is highly dependent on tolerances of your printer and the...

This collapsing staff is inspired by Flapjack on the owlhouse All collapsing staff are roughly 44 inches or about 112 cm long fully extended but that is highly dependent on tolerances of your printer and the model. Print SettingsLayer height and...

&nbsp;A collapsing staff inspired by a broom&nbsp;All collapsing staff are roughly 44 inches or about 112 cm long fully extended but that is highly dependent on tolerances of your printer and the model.&nbsp;Print SettingsLayer height and infill at...

A collapsing staff inspired by owlbert from the owl house All collapsing staff are roughly 44 inches or about 112 cm long fully extended but that is highly dependent on tolerances of your printer and the model. Print SettingsLayer height and infill...

This collapsing staff was inspired by a swordfish,  All collapsing staff are roughly 44 inches or about 112 cm long fully extended but that is highly dependent on tolerances of your printer and the model. Print SettingsLayer height and infill at your...

This is an owl house inspired Ferret collapsing staff. I have included both a print in place version much like the old collapsing light sabers and a version that uses a 7/8 inch dowel. The print in place version is about 88cm when fully extended.

This is an owl house inspired Ferret collapsing staff. I have included both a print in place version much like the old collapsing light sabers and a version that uses a 7/8 inch dowel. The print in place version is about 88cm when fully extended.

A collapsing Penguin/peep staff. ...&nbsp;No supports needed.</p><p>Print Settings</p><p>Layer height and infill at your discretion, I use 0.3mm layer height and 7% infill</p><p>Make sure your line width in cura is set to 0.5mm and extrusion width is...

This collapsing staff was inspired by a pineapple, all credit to this idea goes to Makeitmichael https://www.tiktok.com/@makeitmichael and my wife for thinking the turtle staff looked like a pineapple&nbsp;All collapsing staff are roughly 44 inches...

Inspired by The Owl House this collapsing staff features a Hammerhead shark.Fully extended the staff is about 60cmPrint SettingsLayer height and infill at your discretion, I use 0.3mm layer height and 7% infillMake sure your line width in cura is set...

This collapsing staff was inspired by a mouse&nbsp;All collapsing staff are roughly 44 inches or about 112 cm long fully extended but that is highly dependent on tolerances of your printer and the model.&nbsp;Print SettingsLayer height and infill at...

This collapsing staff was inspired by a swordfish,&nbsp;&nbsp;All collapsing staff are roughly 44 inches or about 112 cm long fully extended but that is highly dependent on tolerances of your printer and the model.&nbsp;Print SettingsLayer height and...

This collapsing staff was inspired by a turtle, this is a challenging print in the beginning so watch and make sure all rings attach around 4.2-4.4mm in heightAll collapsing staff are roughly 44 inches or about 112 cm long fully extended but that is...

This collapsing staff was inspired by a dolphin&nbsp;All collapsing staff are roughly 44 inches or about 112 cm long fully extended but that is highly dependent on tolerances of your printer and the model.&nbsp;Print SettingsLayer height and infill...

This collapsing staff was inspired by a squirrel,&nbsp;&nbsp;All collapsing staff are roughly 44 inches or about 112 cm long fully extended but that is highly dependent on tolerances of your printer and the model.&nbsp;Print SettingsLayer height and...

This collapsing staff was inspired by a goose&nbsp;All collapsing staff are roughly 44 inches or about 112 cm long fully extended but that is highly dependent on tolerances of your printer and the model.&nbsp;Print SettingsLayer height and infill at...

This collapsing staff was inspired by a red panda&nbsp;All collapsing staff are roughly 44 inches or about 112 cm long fully extended but that is highly dependent on tolerances of your printer and the model.&nbsp;&nbsp;Print SettingsLayer height and...

This is a collapsing staff inspired by a squid. ...&nbsp;</p><p>Print Settings</p><p>Layer height and infill at your discretion, I use 0.3mm layer height and 7% infill</p><p>Make sure your line width in cura is set to 0.5mm and extrusion width is set to...