collapsible lightsaber 3d models

**Please read the printing instructions below carefully.** This differs from the Collapsing Lightsaber from John Mulac (3DPRINTINGWORLD) in two main ways: 1) It is printable on a small printer with a print volume of 15cm x 15cm x 15cm, while the hilt...

This is a collapsing lightsaber inspired by 3DPRINTINGWORLDS design. i wanted to print his but found it used loads of material that i wasnt willing to use, so i designed this smaller model (approx 50cm long) that uses a lot less. i also adapted parts...

A bit of epoxy putty put mine back together with no subsequent problems.The largest collapsing blade segment actually sits on the rim of the flashlight cap with this design, which makes it protrude a couple of millimeters forward of the end. I was...

The largest collapsing blade segment actually sits on the rim of the flashlight cap with this design, which makes it protrude a couple of millimeters forward of the end. I was too lazy to fix the file (sorry) but after installing my "bladelock"...

A bit of epoxy putty put mine back together with no subsequent problems.The largest collapsing blade segment actually sits on the rim of the flashlight cap with this design, which makes it protrude a couple of millimeters forward of the end. I was...

This is a 10:1 scale of the Lego Lightsaber with a collapsing blade. It has a screw on cap so the blade can be printed separately then inserted or replaced. I did make the blade a little longer because at 10 times scale it would only have been 12.5”...

I split the model by color so I could print everything individually and not have to paint anything. ...Hopefully I didn't mess anything up, but i turned out pretty good on mine.

Collapsing Sith Lightsaber (Removable Blade) by 3DPRINTINGWORLD in separate parts for easy printing! Thank you 3D Printing World!!! ...

This is a fresh spin on 3DPRINTINGWORLD's excellent Collapsing Sith Lightsaber (Removable Blade) model. I wanted one for a color print so I took the lead and threw this together. Some of the small details didn't translate well, so I had to start from...

The original model: Flashlight Mod for Collapsing Lightsaber is available here: https://www.thingiverse.com/thing:3733269 This rechargeable flashlight cap is designed for use with 3DPrintingWorld's Collapsing Sith Lightsaber (Removable Blade) found...

Be in the safe side and don't left it charging unattended.Print instructionsPrint Settings– Layer height: 0.2mm– Supports: no– For the blade I recommend translucid PETG in spiral vase mode with 0.85mm extrusion width.– This version uses the full...

A slight remix of the original Collapsing Sith Lightsaber (Removable Blade) by 3D Printing World that fits the plate of a Prusa Mini. I sliced around 15mm of the middle of the lightsaber hilt and modified the blades to fit the hilt and each other.

I wanted to print a half-size Collapsing Sith Lightsaber. ### Printing the Handle * Print the handle at 50% scale in x, y, and z dimensions. - I found that using a raft kept it from falling over. * Print the cap at 50% scale in z but 48% scale in x...

Lightsaber with removable cap Supports needed for cap Blade parts can be printed separately

...... I got this idea from a comment by swordgon from this design https://www.thingiverse.com/thing:3606120/comments This lightsaber is fully working by extending and retracting. You swing it out to extend and to retract carefully push the blade back in.

The main print this has been remixed from has been removed. Print in TPU I used supports everywhere @ 20% As is you have to pull it apart after it prints, and I like it that way. Also this was made for the heavy hilt, don't know if that...

Print in TPU or other flexible material. I printed with supports on at 20%, they were very easily removed afterwards. The cuts are thin lines I needed to lightly pull apart after the print. I like it this way. ... This print holds the blades from...

I printed two of the original version and one broke coming off the build plate and the other broke when my son dropped it at a Star Wars event. I have uploaded a thicker version of the hilt as well as two rings that can be used to repair the original...

<p>I printed two of the original version and one broke coming off the build plate and the other broke when my son dropped it at a Star Wars event. I have uploaded a thicker version of the hilt as well as two rings that can be used to repair the...

I printed three replicas, but unfortunately, two of them suffered damage: one cracked during removal from the build plate and the other was badly damaged after my son accidentally dropped it at a Star Wars convention. ...To help repair or replace broken...

Shoutout to 3DPRINTINGWORLD for producing and sharing the original:\r\nhttps://www.thingiverse.com/thing:3604015\r\n\r\nA fresh handle designed in SolidWorks is seamlessly integrated with the blade in Microsoft 3D Builder. ...The result prints just as...

This model is from 3DPRINTINGWORLD on Thingiverse: https://www.thingiverse.com/thing:3668138 The model comes in 2 parts: blade and hilt. The hilt is in 2 parts: the body and the cap. The body and cap are threaded, so you can screw them on. The...

I made an effort to grasp the handle firmly with more force and pressure on my fingers.

I tried to get a bigger hand grip

I scaled down the Collapsing Sith Lightsaber from 3DPRINTINGWORLD to fit my FlashForge Finder's 140mm build area, which was too small for the original model. I broke up the blade into sections, each measuring 140mm or less, and added two more to...

This is a robust set of distinct blades engineered specifically for disarming Sith lightsabers.

The assembly includes a robust and distinct set of blades designed specifically for disassembling a Luke Skywalker lightsaber.

A collapsing lightsaber, model Mace Windu, based on 3DPRINTINGWORLD's original idea. The hilt is designed from scratch, but the blade can be re-used. Designed using FreeCAD, the project file as well as my own FreeCAD template are included.</p> <p>It...

Remixed with removable cap Supports needed for cap Blade parts can be printed separately in vase mode

Here are the separated Blade parts for those who tried to print them together but failed !!THE ORIGINAL MODEL IS FROM 3DPRINTINGWORLD. ...IT IS NOT MINE !!