collapsible coat hanger

Joel 3D Printing Figurine | Assembly
gambody

With Joel being depicted in his typical winter medium weight coat, it is clear that the 3D artist went for the pivotal moment in the game when the protagonist was badly wounded. Still recovering from the serious injury, it is no wonder that Joel...

Hume Beam’s Gantry Upgrade for Qidi X-Max
prusaprinters

Fixing the oversized section was pretty easy using fine sandpaper like this: https://www.amazon.com/dp/B085Y5PLFD?ref_=cm_sw_r_cp_ud_dp_TKB7JFHKZSRNJ94B80HRUnder sized sections can be built-up with multiple wiped on coats of thin CA glue followed by...

Bigger Bertha Rocket (with camera)
prusaprinters

Try to gauge with your eye whether it is on straight while the glue dries.Once the first couple of drops are dried, apply a generous coat of superglue around the adjoining edge. Carefully tipping the rocket body to allow the superglue to dry and...

Icarus - QIDI X-Plus / I-Mate (S) Carriage for Orbiter 1.5 & Dragon / Mosquito
thingiverse

5015 blower fan 24V AliExpress AliExpress Dragon heatbreak AliExpress AliExpress Dragon heatblock AliExpress AliExpress Plated Copper T-V6 Nozzle AliExpress AliExpress Banggood Hardened Steel T-V6 Nozzle AliExpress AliExpress Banggood Energetic QIDI...

Hercules - QIDI X-Plus / I-Mate (S) Carriage for BMG & Dragon / E3D V6
prusaprinters

The other parts are spares that are good to have on hand except for the Energetic PEI sheet which is recommended.24V 5015 blower fanAliExpressTitan Stepper Motor 23 mmAliExpressPlated Copper T-V6 NozzleAliExpressHardened Steel T-V6...

Fun Face Masks for 3D Printing | Assembly
gambody

(4) Cover the surface of the mask with thick coats of clear lacquer. (5) Use any rubber material (e.g. rubber window padding tape) to apply the rubber seal around the edge of the mask. Make sure you use non-toxic silicone or glue. (6) Seal the area...

Grumman F6F Hellcat : Scale Flying Aircraft (1000mm)
thingiverse

leaning towards a roll hangar9 parklite thermo coating Ive had sitting around for years, people flinging all kinds of ideas at me how to cover this thing some sound crazier then others. tissue paper and dope, monokote, packaging tape, tin foil...

Geodesic(k) RGB LED Spheres
prusaprinters

Many new challenges popped up, because it will be different... ========================================== Printing & assembling Parts to print For the small (2V) geodesic sphere you have to print these parts: 2 x gs-2v-125mm_ring-01.stl 2 x...

Pan & Tilt w/NEMA17 Steppers
prusaprinters

Coat the top side of the nut with PVA glue (like Elmer's) before the print is resumed, so the plastic sticks to it. Chase the threads with a 1/4-20 tap after printing in case any glue ran into the threads. I print with a 0.4mm first layer and 0.2mm...

Swatch + Modifiers - Filament/Infill - Customizable OpenSCAD
prusaprinters

This will allow a z-based color change at height 1.8, with 2 layers of "coating" in different color, that won't affect the swatch sampling panels.Card (thin): A thinner version of the credit-card sized swatch, this one prepared to print at a 0.1mm...

Lofipi lo-fi speaker
prusaprinters

Adding additional coats will darken the stain, if you like. You don't need to stain the inside of the enclosure.</p><p>Screw four M2.5x10mm screws into the four screwholes on the bottom side of the Lid, but don't screw them in quite all the way...