coleman pool hose adapter 3d models

I made these hanging hangers for my pool hoses because the cheap version from the local store didn't last. The design has three clips in total, which gives it a height of 230mm. If you have a smaller print bed, you can cut this down to two clips...

http://www.thingiverse.com/apps/customizer/run?thing_id=834725 Using the following settings: Loop_position set to 10, Text to COLEMAN Height set to 4 different values, each measuring from 7.5 to 14 units. Twist set at a value of -7.5 units. Spacing...

This is a remix of Blue Waves/Summer Waves-Intex Pool Cleaner Adapter by bdub_24 that has a male garden hose attachment on the end instead of what it had before. I cut the end off of the garden hose adapter by jackout to get the garden hose part.

I've made some adjustments after testing this piece and discovered that it doesn't quite work as intended due to excessive resistance in the small hose, causing all water to flow through the larger hose instead. ...My heat-exchanger has a few issues...

To allow my hoses to dry completely after removing them from the pool, I wanted a solution that would work well for this task. This design meets those needs perfectly, so I'm sharing it with others. It's printed with a .20 layer height and 20%...

I lost the valve adapter for my Coleman 4D Universal Quickpump, so it wouldn't inflate my Coleman air mattresses effectively anymore. I pulled out OpenSCAD and printed this thing in time to sleep for the night! It works best printed with PLA (the ABS...

connection to have a more powerful pump that stirs the water at the bottom of the pool pipe diameter 32mm

I need this adapter to connect a pool heater with a fire basket and a stainless steel corrugated pipe, or solar DN25. It joins the thread G 1 1/4" with the standard hose (32 mm) from Intex. The adapter file has a thin support layer for better grip.

(to wrap hose) - 47.11mm (1.85")Length - 126.7mm (5")1" (25.5mm) gap down the center to squeeze in the hosePrint settings I used (adjust as needed)200 / 60 tempsNo Supports / Adhesion15% infill to give buoyancePlaced on 4 foot hose section closest to...

Bracket to keep filtration system inlet and outlet pipes at right angles with 32 mm to 38 mm adapter Pipe diameter 38 mm Fixing ring diameter 66 mm

Good for 1 1/4 pool vacuum hose. ...Adapter is for above ground intex coleman pools.

Customized version of https://www.thingiverse.com/thing:125509 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=125509

This is a personalized rendition of the design found at http://www.thingiverse.com/thing:125509. It was created using the Customizer tool, available at http://www.thingiverse.com/apps/customizer/run?thing_id=125509. The specifications used for this...

Customized version of https://www.thingiverse.com/thing:125509 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=125509

Customized version of https://www.thingiverse.com/thing:125509 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=125509

This customized design is based on Thingiverse's model with ID 125509, which you can access at http://www.thingiverse.com/thing:125509. The customization was done using the Customizer app available at...

A personalized rendition of http://www.thingiverse.com/thing:125509 was crafted using the Customizer at http://www.thingiverse.com/apps/customizer/run?thing_id=125509. ...Specific parameters include a height (h0) of 80, radius (r2) of 13, and an angle...

Customized version of Thing:125509 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=125509 Directions Operating using settings: h0 = eighty r2 = ten th = two and a half

A personalized rendition of http://www.thingiverse.com/thing:125509 was crafted using the Customizer tool at http://www.thingiverse.com/apps/customizer/run?thing_id=125509. ...The specifications include a thickness (th) of 4, a height (h0) of 60, and an...