coleman cooler drain cap 3d models
104259 3d models found related to coleman cooler drain cap.thingiverse
Replacement drain plug for coleman cooler. ...Print upside down.
thingiverse
The plug on my Coleman chest cooler broke, and the few that I found on Thingiverse didn't fit my cooler, so I made one to replace it. It snaps over the cooler drain nipple quite firmly, and you can add a rubber o-ring for an even tighter seal. I...
thingiverse
The cap is specifically designed to be manufactured using TPU/TPE material for a Coleman Cooler to prevent water from escaping.
thingiverse
This is a speedy design for replacing a drain plug on a Coleman cooler, perfect for any cooler with a 10mm diameter outlet. You can't deny it - we've all misplaced one before! ...This model prints out fast, without the need for supports, in just a few...
thingiverse
Igloo cooler users have found success using this specific replacement cap to fit securely into the drain opening, preventing water leaks and damage. ... The detailed design has been made available in a Sketch-Up format, allowing users to explore the...
thingiverse
Customized version of https://www.thingiverse.com/thing:2010734 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2010734
grabcad
A 50-quart ice chest/cooler is available for those who need ample storage space. Don't forget to show your support by clicking the '♥' button if you find this model appealing! ...Your gesture means a lot to us.
thingiverse
This is a replacement drain plug cap for a Igloo BXM cooler. It may also fit other Igloo cooler and even other brands, but that has not been tested. Threads are tighter than original, but operate smoothly. The addition of a 26mm OD O-ring or...
prusaprinters
This is a replacement drain plug cap for a Igloo BXM cooler. It may also fit other Igloo cooler and even other brands, but that has not been tested. Threads are tighter than original, but operate smoothly. The addition of a 26mm OD O-ring or other...
thingiverse
Replacement Hinge for Cheap Blue and White Coleman Coolers Model 6277/6278.
thingiverse
The Coleman cooler boasts a drain featuring an outside diameter of 17mm and an inside diameter of 13mm. To enhance functionality, I revamped the original design by incorporating a reinforced tab with a carefully drilled hole, allowing for secure...
thingiverse
This is a simple piece. ...It's the handle to the telescoping handle of my Coleman Cooler
thingiverse
This hinge was designed for the Coleman 5-day cooler but should work for most Coleman coolers that use the same type of hinge. Print Settings: Printer Brand: RepRap Printer: Prusa i3 Rafts: No Raft Supports: No Support Resolution: 0.25mm Resolution...
thingiverse
Replacement handle and plugs for a Coleman cooler 119.8mm between the mount points and 9mm holes v5 plug has a longer thicker section to fit more securely
thingiverse
Customized version of https://www.thingiverse.com/thing:2010734 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2010734
thingiverse
Spacer needed to upgrade Coleman cooler's wheels to steel. ...The existing axle is a sturdy 5/16-inch rod, which will accommodate larger 1/2-inch bearings for the new steel wheels.
thingiverse
The prop was tailored to fit snugly onto the front edge of the Coleman 50qt Xtreme wheeled cooler, but it should work equally well on many other Coleman Xtreme series coolers too. ...And, I suspect it'll be compatible with a wide range of others as...
thingiverse
This is a print-in-place "pinned" hinge for Coleman coolers. This is designed to have the same opening stops that the original hinge has as well as to be very strong when printed with either PLA or PETG. ... There is also a version of the hinge...
thingiverse
I designed this to replace the old handle on the coleman xtreme 50 qt wheeled cooler because mine broke:( But this new handle fits great and overall feels a whole lot more sturdy! It was a snug fit and there are holes to screw it back in. Designed in...
prusaprinters
So, I designed a prop to hold the lid open partway to allow air to move through and prevent this. The prop was designed to fit onto the front lip of the Coleman 50qt Xtreme wheeled cooler, but I think it will fit just as well on many of the other...
thingiverse
Replacement hinges for my old (25 year) Coleman Thermoelectric Cooler. Printed this in ABS and it's holding up so far; painted parts with acetone to enhance layer adhesion. Print twice for each hinge; both halves are identical. Intended to...
thingiverse
This particular model features the iconic handle from those classic Coleman coolers, which have been a staple in outdoor adventures for years. My recommendation would be to use a high infill setting to achieve the desired level of detail and realism....
thingiverse
A look at some online tutorials gave me hope – many other people have struggled with getting their Coleman coolers' handles working correctly without major modifications or hacks, and these problems range from an incorrect amount of lubricant to...
thingiverse
The lid latch on my Coleman 150 (5 day) cooler was broken, so I took it apart and measured a new one up and modeled it in 3D Builder. Then sliced in prusa slicer at .1mm layer height (2.5 hour print). Print with supports on bed only with...
thingiverse
Remixed https://www.thingiverse.com/thing:5030606 because I needed this to be a plug to seal the Coleman. ... No changes done to Lauter_Nut_No_Support.stl, I just included it for convenience here too
thingiverse
I wanted a plug for my cooler that was a little more secure than the stock plug. ... This one fits very tight and should work well.
thingiverse
I built this retro cooler because I have one that I adore, so now I also have a 1/10 scale replica of it. You can toss it into the bed of your RC crawler. It measures 66X40X44mm. It was initially printed as one piece, but I broke it down into...
thingiverse
Crafted exclusively to pair seamlessly with the Coleman 54 Quart Cooler.