cobra in 3d

If you appreciate this model and wish to see it in action, please write some lines of code and share your work. If you have any questions or concerns about the assembly process, feel free to leave a comment, and I'll respond promptly. If there's...

MotivationPrinted this ladder foot pad replacement parts in PLA. WARNING: Be aware that PLA is quite slippery compared to the rubber-like plastic I had before but as it was broken I wanted it replaced by something more massive. It also lacks...

[1] Designer of Wheel Chocks for safe Transport in your car created it and shared it on Thingiverse at http://www.thingiverse.com/thing:148639, allowing others to use it under Creative Commons - Attribution - Share Alike. [2] Inventor of the Hex...

Insert it into the four holes in the corners of the middle part and cut 2mm above the surface. Then glue the middle and top parts together.</p><h5>Axles</h5><p>Two axles need to be created. The axle consists of two printed wheels and a metal axis...

... with black for better contrast. R2 Sketches: (choose one and rename the .txt with .ino) activeradar-hx-48-r2-ino.txt (48 cm range) activeradar-hx-96-r2-ino.txt (96 cm range) I'll leave the original sketches in case they are preferred. ... <hr>

Part should be laid on slicer in this manner that small bolt will touch bed. Do not use Brim or something else. After printing, remove the small bolt with a cutter-knife and use sandpaper to get structure smooth. If you are printing these parts with...

The idea is to place the box in a dark place and uses the sensor to wake the effect up a programmable distance.The fourth generation of the case for Adafruit's Animated Eyes Bonnet for Raspberry Pi provides for an interchangeable solution to protect...

you'll need 6x6x5 tact switches -...

All parts but roller_mount_inside and roller_mount_outside are done from scratch in onshape.I was looking for a solution for a filament drybox where i can also rewind the spools. The best solution for a box seemed the IKEA 365+ 10.6l box because of...

You can load your chosen code into this chip, such as: rainbow, fire flames, and many more. °°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°° RAINBOW CODE FOR ARDUINO NANO HERE: include &lt;Adafruit_NeoPixel.h&gt; include...

These cap openers are designed to fit Dainichi humidifiers, which have the largest market share in Japan. These humidifiers may not be widely used outside of Japan. ... [Japanese] ...

So I widened the inner channel in this version to 12.33mm for a snug fit on my MK3 bed rail. The prints made on my MK3 fit so tightly that they don't seem to need the screw called for by the original design. Instead, I've added two recessed zip tie...

Design for FDM Printing “Give me a Lacerta and a crew of five, and I’ll drive it to Hell and back.” – George Hashigawara, GEO-Corp prospector     The Lacerta-type is the most popular of FKMSA’s “ground crawler” line, a selection of rough, rugged,...

This way, you can remove one hard drive and put it back in without taking the entire thing apart. Print Settings Printer Brand: Printrbot Printer Model: Simple Black Rafts: No Supports: No Resolution: 0.3mm Infill: 15%-25% Notes: I recommend using...

It works in my head, but if you're still confused, let me know. How I Designed This My shift ferrules are 12.77 mm long, 5.78 mm OD, 1.80 mm cable hole, and 4.28 mm ID. This hookup may not work for other shift ferrules (larger OD). The shift hookup...

Stl needs to be cut using the cut tool in slicer to for most build plates.&nbsp;This main spring Mcmaster 9637K172 Pins with this size Mcmaster 97395A45432mmOD, 26mm ID aluminium tube. ...approximately 12 inches...

The screw secures the bolt into the assembly and acts as a bolt handle that slides back and forth in the slots and serves as mounting point(s) for the elastic bands. A Bic Mechanical Pencil acts as an optional barrel sleeve (outer pencil casing) and...

In the bottom of the frame, there are 3 holes for strong neodymium magnets. If you glue three magnets to your enclosure with a 3M tape, you can easily attach or remove the spool holder. It is especially useful when you have multiple printers. To...

Tips are also appreciated if you'd like to see more files from me or if you would like to request changes or updates to files!Tip Via Stripe&nbsp;Tip Via PayPalA “Nintendo Switch ring holder with different angles.” Simple.This version removes the...

***If you appreciate what I'm doing, consider buying me a coffee, and check out my other models for something else you might like!**********AUTOMATIC HEATER FOR THE ORIGINAL PRUSA ENCLOSURE USING THIS POWER SUPPLY MOUNT COMING SOON!**********The MK4...

When it pauses, insert a gold piece into each in-progress stonework - this will create a slug of little gold coins inside the vault. Be careful not to mess this up - if you don't get the gold slug seated all the way, it could interfere with your...

As you can imagine, the cards were constantly ending up in a huge mess! Well, not any more! We created this card dispenser to keep things a little more organised, but we soon realised that card dispensers are useful for many games and even for...

I've been using it as a bedside shelf for a few months now and it works really well for my needs.I still haven't finished the LED lighting under the shelf but I will get back to that when I get a chance.I will make some different variations to the...

verwendeter Klingen liegt in eurer eigenen Verantwortung. Ich übernehme keinerlei Haftung für Sach- oder Personenschäden. Dies ist ein Remix unterschiedlicher Ideen: - Das Grundmodell basiert auf dem K.U.T. von LarkysPrints ...

A JIS 0 or PH 0 screwdriver is needed for removing the original mount and installing this one. Installation orientation is dictated by the orientation of the model in the provided STL file (positive Y is the top of the lens, the screw-hole on...

😊 assistant In response to your request for rewriting a text while maintaining the original text, I have provided multiple variations within the 60-word limit in my previous responses. If you require additional assistance or clarity, please don't...

These new pieces have been designed to be compatible with GW pieces in terms of their measurements. The height of the low wall is 61mm, which matches the height of Zone Mortalis or the Dome. The high pieces measure 122mm, equivalent to the height...

These can also be defined in a single array with from/to pairs: `[ [from, to], [from, to], ...]` For those who do not want to use OpenSCAD to create .STL files for their printer, I uploaded some samples for screw holes (single or double screw) and a...

Insert it into the four holes in the corners of the middle part and cut 2mm above the surface. Then glue the middle and top parts together.</p><h5>Axles</h5><p>Two axles need to be created. The axle consists of two printed wheels and a metal axis...

[Part_7R8R] - Width (X): 124,64mm; Lenght (Y): 81,36mm; Height (Z): 154,74mm Features:- Highly detailed miniatures- Pre-supported and ready to print files- Each miniature has been test printed and quality verified- Designed for 32mm scale Files are...