cobb mount 3d models

Single-sided tape is not enough; instead, use a small zip tie to secure the mount to the dashboard. No modifications are needed to the dash itself, just cinch the zip tie into the gap between the panels and trim the end as shown. The design is...

Replace the factory dash defrost vent in your 2002 - 2008 Subaru Forester SG / XT and mount your Cobb Accessport. Includes the LH and RH versions with .stl and .step files No hardware is required. Simply pop out the stock vent and this will clip...

... This vent mount perfectly matches the fit and finish of the OEM vent and makes installing your Accessport super simple. This mod is perfectly reversible and will not harm the original parts. The factory defrost function works perfectly still.

Replace the factory dash defrost vent in your 2007 - 2014 Subaru Impreza WRX/ STI and mount your Cobb Accessport. Check photos to make sure this is the correct part for your car. Includes the LH and RH versions with .stl and .step files No...

Uses two M4-0.7 Thread Size, 25 mm Length, Fully Threaded screws and nuts to secure the lower brace in place and thus grip the mount securely onto the vent opening. Use a filament with a high melting point or the lower brace will warp and bend when...

I've made some adjustments to adapt it to US/left-hand drive and utilized the new mount design for the accessport holder. It works great, although securing both sides can be challenging. To make up for this, I discovered that the rubber molding...

If you want to mount your AP high up without blocking the AC vent.Use a piece of tape to mark installation position prior mounting.Foam double sided tape isn't necessary.Enjoy!

Cobb Accessport securely fastens to vents using supplied mount.

This is for the Cobb Access port, no ball bearing needed. ...Just use this to slide the access port as a vent mount

This is a replacement ball mount for the COBB Accessport. Print two and cement together, no supports are needed. I recommend 5 or more perimeters and a rigid, heat-resistant filament. ...FreeCAD file is included.</p> Category: Automotive

This is a replacement ball mount for the COBB Accessport. Print two and cement together, no supports are needed. I recommend 5 or more perimeters and a rigid, heat-resistant filament. ...FreeCAD file is included.

I designed this to adapt Cobb-Accessport style mounts to hold my phone. I designed the phone-mount portion to fit my iPhone X in its case, so it's unlikely that it will work for other people. It's designed to be assembled with M3x4mm low-profile...

This is a 2015+ WRX defroster vent mount for a Cobb Accessport remixed from dasfruit. I added vent fins, enclosed the portion of the mount around the cable holder, and added a clip to keep the cable from coming out of the mount. I also added tabs...

This object was crafted utilizing the advanced features of Tinkercad, a cutting-edge 3D design software. ...Users can easily edit and refine their creations directly within their web browser at https://www.tinkercad.com/designs/57yMHIEvPsr.

Universal roll cage mount for Cobb Accessport. ... -Includes two sizes (40mm/1.57" and 44.45mm/1.75") -Universal vehicle fitment -Retains your factory magnetic cradle included with the Accessport -Will require hardware x4 - M5 x 12mm Screws...

Couldn't find any angled mounts for my Cobb APv3 so I decided to make my own! The 90 degree bracket is probably the easiest solution however is limited to flat areas, the ball joints offer the original mounting capabilities of the v3 mount but with...

This is a single 8mm Cob Cobb Strip Led Holder Mount. Was made for the smaller common cobs roughly 8mm x 60mm. Has channels in the back that allow the wires to come thru etc. Prints great in PLA lying on its back. ... There are a few different...

This design is a remix of thing 3542130, with modifications that include incorporating a contoured section from that original model and creating a more robust mounting mechanism specifically suited for left-hand drive STs. ... Print two identical...

Shim to improve suction on a windshield mount for the Cobb Accessport in the case it has lost some of its grip. ...:)

Increase suction power on a windshield mount for the Cobb Accessport by enhancing its gripping ability if it's started to lose hold.

I'm installing a Subaru WRX side defroster vent mount on my Cobb Accessport, and I've found that it fits perfectly without needing any additional hardware. The vent holds the accessport securely in place. I've tested this setup on my 2018 WRX model.

I created this attachment to securely fasten to your side pillar plastic, featuring a ball socket that fits perfectly onto the AccessPort mount. Feel free to modify or slice this design as needed - it's all about functionality, not aesthetics. For...

Adjustable Cobb Tuner Mount for Subaru Impreza STi (2008-2014) Also Fitting Forester XT Models (2003-2007) with Precision Key Features Include: A 175° Adjustable Base Mount Provides Customized Alignment 2-Point Locking Arm Ensures Secure and Rigid...

Please note that this is specifically designed for the Cobb access port mount only - the white mount shown is actually a cup holder mount, but I don't think it will fit other vehicles as well as it does my 1996 Subaru Impreza. ...If you're interested...

This is a part I prototyped to mount the Cobb Accessport v3 in my 2004 Subaru STi. It is a 3D printed part that fits to the switch blank found in this model year made for the Canadian market only. This switch position is used for HID headlight...

28mm civilian with a musket. Base not included. ...Presupported file included.

Customized version of http://www.thingiverse.com/thing:548191 Created with Customizer! http://www.thingiverse.com/apps/customizer/run?thing_id=548191 Using the following settings: Thick material, 0.5 mm. Height: twenty millimeters. Letter...

Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=548191 Instructions Using the following options: size = small note19 = S note18 = N note17 = O note16 = C note15 = - note14 = N note13 = O...