cobb accessport holder 3d models

A Cobb AccessPORT holder allows mounting on the left vent grille near the steering wheel in '02-03 Subaru WRX models; possibly compatible with later versions. The cord clip enables easy unplugging when not driving to avoid screen damage, and keeps...

This is a holder designed specifically to accommodate your Cobb Accessport V3, attaching neatly to your air vent. It's definitely a better option than attempting to secure it with adhesive tape. The "low profile" lp version is the v2 model, which...

This is Reeseallen's design including v4.3 of the holder and v3.6 of the clips condensed into 1 layout. ... Instructions Print, then use acetone or superglue to attach the clips to the holder.

Cobb Accessport securely fastens to vents using supplied mount.

This is a replacement ball mount for the COBB Accessport. Print two and cement together, no supports are needed. I recommend 5 or more perimeters and a rigid, heat-resistant filament. ...FreeCAD file is included.

This is a replacement ball mount for the COBB Accessport. Print two and cement together, no supports are needed. I recommend 5 or more perimeters and a rigid, heat-resistant filament. ...FreeCAD file is included.</p> Category: Automotive

This is for the Cobb Access port, no ball bearing needed. ...Just use this to slide the access port as a vent mount

This part is compatible with reeseallen's AccessPORT holder.http://www.thingiverse.com/thing:37769 ...and was used to derive this design. A great addition to an awesome dash mount... Let's see the V3 do this! ...

This is a 2015+ WRX defroster vent mount for a Cobb Accessport remixed from dasfruit. I added vent fins, enclosed the portion of the mount around the cable holder, and added a clip to keep the cable from coming out of the mount. I also added tabs...

I created this STL file as a free simple fix to a known issue with the Cobb Accessport cable breaking it's original tabs. Leave a comment if this helped you or if you run into any issue with printing these. If you need this part 3d printed and do...

I designed this to adapt Cobb-Accessport style mounts to hold my phone. I designed the phone-mount portion to fit my iPhone X in its case, so it's unlikely that it will work for other people. It's designed to be assembled with M3x4mm low-profile...

I'm installing a Subaru WRX side defroster vent mount on my Cobb Accessport, and I've found that it fits perfectly without needing any additional hardware. The vent holds the accessport securely in place. I've tested this setup on my 2018 WRX model.

Universal roll cage mount for Cobb Accessport. ... -Includes two sizes (40mm/1.57" and 44.45mm/1.75") -Universal vehicle fitment -Retains your factory magnetic cradle included with the Accessport -Will require hardware x4 - M5 x 12mm Screws (MCM* -...

Tired of dealing with a loose ball joint that comes with your Cobb AccessPort? I created this attachment to securely fasten to your side pillar plastic, featuring a ball socket that fits perfectly onto the AccessPort mount. Feel free to modify or...

A custom mount for a V2 accessport on my 2010 Subaru STI. Single-sided tape is not enough; instead, use a small zip tie to secure the mount to the dashboard. No modifications are needed to the dash itself, just cinch the zip tie into the gap between...

Replace the factory dash defrost vent in your 2015+ WRX/STi with a custom vent that can hold your Cobb Accessport in an easy-to-reach and view location. No hardware is required. Simply pop out the stock vent and this will clip back in its place.

Replace the factory dash defrost vent in your 2002 - 2008 Subaru Forester SG / XT and mount your Cobb Accessport. Includes the LH and RH versions with .stl and .step files No hardware is required. Simply pop out the stock vent and this will clip...

Replace the factory dash defrost vent in your 2007 - 2014 Subaru Impreza WRX/ STI and mount your Cobb Accessport. Check photos to make sure this is the correct part for your car. Includes the LH and RH versions with .stl and .step files No...

This is a part I prototyped to mount the Cobb Accessport v3 in my 2004 Subaru STi. It is a 3D printed part that fits to the switch blank found in this model year made for the Canadian market only. This switch position is used for HID headlight...

I've made some adjustments to adapt it to US/left-hand drive and utilized the new mount design for the accessport holder. It works great, although securing both sides can be challenging. To make up for this, I discovered that the rubber molding...

If your cable release clip has snapped, don't waste money on a brand-new cable - instead, try this inexpensive fix that will get your camera working like new again.

Print in PETG/ABS at high temperature to ensure strong layer adhesion. Assemble the parts using solvent-based adhesive, then sand them down to a smooth finish before applying paint as desired. This design is a remix of thing 3542130, with...

Similar to the "Cobb slide", made with aluminium sheet (one of those Cobb is in the photos, made from an aluminium can material; courtesy of mr. Cobb and mr. Chas) It is in Openscad and is customizable. Two design types: one "Flush", the...

<p>I found this inventive vent clip: <a href="https://www.thingiverse.com/thing:3880775">https://www.thingiverse.com/thing:3880775</a></p><p>However, it's intended for right hand drive Focus MK3 ST and RS models.<br><br>Since I'm in the US, I sliced...

This is a single 8mm Cob Cobb Strip Led Holder Mount. Was made for the smaller common cobs roughly 8mm x 60mm. Has channels in the back that allow the wires to come thru etc. Prints great in PLA lying on its back. ... There are a few different...

Customized version of http://www.thingiverse.com/thing:548191 Created with Customizer! http://www.thingiverse.com/apps/customizer/run?thing_id=548191 Using the following settings: Thick material, 0.5 mm. Height: twenty millimeters. Letter...

28mm civilian with a musket. Base not included. ...Presupported file included.

Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=548191 Instructions Using the following options: size = small note19 = S note18 = N note17 = O note16 = C note15 = - note14 = N note13 = O...

Customized version of http://www.thingiverse.com/thing:305087 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=305087 Instructions Using the following settings: letter choice four is B letter...