cm4 board 3d models

... CM4 Ether Boards. ...Create your mini Raspberry Pi CM4 server with. This takes 1.5U space of your standard media/server rack.More information about the CM4 Ether Board here:https://dphacks.com/cm4-ether-board-minimalist-compute-module-4-carrier-board/

This model is a low poly to-scale model of the CM4 IO board for prototyping. As follows: IO_Board_Prototype.stl - just the IO board, no CM4 or heatsink and fan CM4+SINK+FAN30mm.stl - just the CM4 with heatsink and fan As usual, the SKP file is...

Case design for CM4 IO board for arduino from Waveshare My first TinkderCAD design.

It's just a basic holder for Raspberry pi CM4 IO board with a holder for PCIe card. ... Parts are press-fitted so you'll need a hammer or something to put it together.

.OpenLaserCase for 52pi CM4 Router Board This is an opensource lasercut case for 52pi CM4 Router Board EP-0146. Dies ist ein opensource Gehäuse für das 52pi CM4 Router Board EP-0146. <br /><br /> For sheets of wood and and the lid in PMMA...

Modified to mount a Raspberry Pi CM4 IO Board to standard ATX mounting points. Versions provided: - Cutouts for larger standoffs using 6# screws in the housing for my build. - Cutouts for more common standoffs using m3 screws (untested). ... ...

Use 4×M2.5 threaded inserts, such as https://www.mcmaster.com/94180A321/ and 4×M2.5 screws (6mm or 8mm length seem good) to secure the board to the tray. Note that some HDMI connectors (in particular) may interfere with the lip of the tray. My...

The design minimizes material, at the expense of leaving some traces &amp; components open on the bottom. Use 4×M2.5 threaded inserts, such as https://www.mcmaster.com/94180A321/ and 4×M2.5 screws (6mm or 8mm length seem good) to secure the board to...

Just a remix of Waveshare Arduino CM4 IO board case for Waveshare Arduino base board

Modified version of geerlingguy's blank IO shield for the Super6C CM4 Cluster Board.

Do you want to protect the bottom of your Raspberry Pi Compute Module 4 IO board but don't want to spend all day printing a case? This is a simple bumper case that has standoffs to support the board. All the numerous ports are still accessible. The...

There hasn't been much of anything available for these due to the chip shortage for the last year or so, but now that CM4s are trickling out into the wild I thought I'd pick one up and finally finish my router board build. ...&nbsp;No supports, print...

Modified Version for Raspberry Pi CM4 IO Board. ... Adapted to this mounting solution: https://www.thingiverse.com/thing:4949020 2021-12-14 revised version V2 added: - moved everything a bit to the right - removed antenna notch - added led...

With my previous experience and interests in designing LEGO Robotics expansion hardware, I developed a Raspberry Pi CM4 Carrier board specifically for the LEGO SPIKE Prime educational system. In short, this is a slim, self-contained add-on to the...

My first attempt at making a box from the PCB 3D file

I designed the Lid of this case to hold a 60mm fan directly above the CM4 with a 15mm tall heatsink on top of the CM4. I printed this case out just fine on my Ender 3 Pro and it fits the board perfectly. I did NOT create any openings in the case...

... Case. ...&nbsp;This was designed to fit the WaveShare CM4 IO board with PI 4 Compute Module. &nbsp;The case has a 40mm fan design to blow air across the top then around the side and to the bottom to cool the NVMe installed on the bottom or the board.

This is just a simple stand that holds the Touchscreen as well as the IO-Board. ... I use this for developing for the cm4.

DFRobot Mini Router V1 + CM4 Case ============================== This is a minimalist case I designed for the DFRobot Mini IoT Router Board V1 that utilizes the Raspberry Pi CM4 board. I wanted a case that was clean and simple but still provided full...

!!!Can not Be Used with SD Card, use internal Flash or M.2 on the Back as Boot device, Remix encouraged!!!Case for the following  IO Board:https://www.waveshare.com/cm4-io-base-c.htmNeeded Hardware:4 M3x6 Socket head Screw(Or similar)4 M3 Heat Set...

Case for a dual-gigabit router using a [Raspberry PI Compute Module 4](https://www.raspberrypi.com/products/compute-module-4/?variant=raspberry-pi-cm4001000) and the [DFRobot DFR0767 "Raspberry Pi Compute Module 4 IoT Router Carrier Board...

##Case for Raspberry Pi CM4 Waveshare Nano Base Board (B) **Assembly** - Print both models - Put the computer in the case (mounted on the Waveshare nano) with the Waveshare board facing the inner face of the case) - Snap the lid on the case with the...

This is a small case for the Waveshare CM4-DUAL-ETH-MINI router board.

This is a simple cooling case for Seeed Studio Gigabit Ethernet Carrier Board for RPi CM4 and it is designed to mount a fan over the case. This is very necessary because the CM4 CPU gets extremely hot without a fan. The fan used in this project is...

This is a case for the ATX Board PIKVM Remote Control ATXA-A+ATXA-B Board for Raspberry Pi CM4 as found on ebay -> https://www.ebay.de/itm/354162821153 Category: Computer

This is The First RaspberryPi case for custom Bitcoin SBC by Mirko_electronics This Raspberry Pi CM4 Carrier Board is Built for Bitcoin FullNode & Lightning network node. The BitPiRat adds two USB ports, an Ethernet port, one HDMI input and an M.2...

Raspberry Pi CM4 dev board (85x56mm) Compatible with standard HAT.Product Design service and customization of CM4 available Please contact me. ...https://github.com/QWaveSystems/QWAVE_Raspberry-Pi-CM4-Altium-Library

Raspberry Pi CM4 dev board (85x56mm)Compatible with standard HAT plug at bottom side.Product Design service and customization of CM4 available Please contact me. ...https://github.com/QWaveSystems/QWAVE_Raspberry-Pi-CM4-Altium-Library

Designed for Raspberry Pi Compute Module CM4 IO Board Layer thickness .3mm Supports Recommended for base Supports not required for lid Sized for 80mm Fan Fanless lid available as well Friction Fit so do make sure printer is dialed in 1st Revision

... the bracket, the CM4 module will bend. The fan is tightly fit onto the poles. The bracket is, in this case, mounted to the CM4 IO board, with a 1,2mm spacer between the CM4 module and the board. ...I used four M2,5 x 10 pan hat screws for this.