cluster hat case 3d models

Beautifully crafted case perfect for housing a Pi0 + Explorer HAT based OpenAPS setup, with ample space to accommodate either a single 18650 or a 21700 Li-Ion Cell. ... To assemble this rig, you'll need: 4x 10mm M2.5 screws 4x 12mm M2.5 screws 4x 10mm...

Enlarged Raspberry Pi Zero W case to accommodate a Waveshare Ethernet/USB hub hat on top.Remixed from: https://www.thingiverse.com/thing:1165227A lot of adjustments from the original model as the port alignment was not good and the case too small.

... by mdkendall. ...The Remix is Tailored to Fit an RS485 CAN Hat Module Perfectly. To Accommodate the IC's and Crystal on the Module, the Top of the Case is 3 mm Thicker Than the Original. ...Check Out the Bottom Part at the "Remixed from" Link Below.

Case for Model B+ with POE HAT insideNeed replace half the original M2.5 screws (x4 longer M2.5x8) to fixed cover case.Modified from Jan Lička's designRaspberry Pi 3 B/B+ caseIf you use Flashforge finder or dreamer with PLA , just print it out and it...

Large Commodore logo on the bottom doubling as an air vent.Use Pan Head Self Tapping Sheet Metal Screws to secure the case - 3mm x 7mm or 8mm (M3)The IO Hat is available on PCBWay...

The Raspberry Pi 3A+ is paired with the Pi1541 IO hat case, providing direct access to all main outputs of the IO hat. This includes two 6pin DIN connectors, five side buttons, two LEDs, and a single OLED connector. Additionally, the commodore logo...

Case for Raspberry Pi 3A+ with BBC Micro Coprocessor Tube Hat giving full access to all the 3A+ ports and the top 40pin connector of the IO hat. ...Also has a BBC Micro logo on top and a larger logo on the bottom doubling as an air vent.Print top and...

Raspberry Pi 2/3B+ with a high-performance BMC 64 IO hat case that gives users complete access to all the ports of the Pi and the IO hat, including two joystick ports and eight navigation buttons. A large Commodore logo is prominently displayed on...

This is a clear-cut case housing for the Pi1541 hat by @edu_arana. Pi1541 is an open-source project created by Steve White, available at https://cbm-pi1541.firebaseapp.com/. This case fits perfectly on Raspberry Pi 3 or a Raspberry Pi 2 model B.

Here is a custom-built case for the P4wnP1 pentesting tool, designed to work seamlessly with the OLED hat. **Electronics Components:** To get started, you'll need the following electronics parts: * A USB A adapter available on Amazon...

... pin supports with screws that secure both components snugly inside. ...Ensured seamless airflow by filling in the fan slot and creating a ventilated space above the hat, while also adding strategically placed slots for enhanced side ventilation.

... to the e-ink screen in my build. ...This case is just for the screen (the one with the HAT). It is not for the pawnagotchi builds. I printed it with a random old PLA on default settings, no supports, rafts, brim.... ... Category: Electronics

... Version of the KISS RPI 4 Case Designed by Gagacr, Featuring a Strategic Hole at the Top for Optimal Cooling. ...This Ingenious Design Ensures Seamless Integration with the Raspberry Pi PoE Hat, Compatible with Both Raspberry Pi 3 B+ and 4 Models.

Case for Pi5 Model B with Cooling Fan HAT Modified from Jan Lička's design (rpi3)Raspberry Pi 5 caseIf you use Flashforge finder or dreamer with PLA , just print it out and it is ready to use. ...I have tested it many times.

... case. ...This specific design is tailored solely for the screen that comes with the HAT, not for any other builds like pawnagotchi. ...Initially, I printed it using an old PLA filament on default settings without employing supports, rafts, or brim.

I really like pyrho's snap fit case, but my NVMe HAT wouldn't fit, so I decided to remix it.I remixed the original model to fit the 52pi N04 M.2 2280 PCIe To NVMe HAT specifically, but other HATs can fit in the case fine as long as you use 17mm...

Simple "stack" case design for the Automation Hat Mini by Pimoroni I designed. I wanted something that was still lightweight but gave the setup enough protection to throw in my pocket and feel sturdy. You'll need: 1x Raspberry Pi Pico 1x Automation...

I bought the MakerSpot Stackable USB Hub HAT from Amazon, which was the top-rated product for a Raspberry Pi Zero W USB Hub HAT at that time. The linked raspberry pi case didn't fit with the Zero4U case on Thingiverse, so I customized it to work...

Raspberry Pi 3A+ with Pi1541 IO hat case giving full access to the main outputs of the IO hat, including the two 6pin DINs, the 5 side buttons, the 2 LEDs & the OLED connector. ...Also has a commodore logo over the GPIO buzzer so it is not covered...

This is a pretty simple little case for a Raspberry Pi 4 with the Yahboom RGB Cooling Hat. This hat features a 40mm x 10mm fan, three addressable RGB LEDs, and a tiny OLED screen that can show several different bits of information about the Pi's...

The fan on the POE+ hat does not work with the Banana pi so I added a 40mm 5V fan to aid in cooling. Fan and case is held with snap fittings, no screws required. I did not expose any of the IO ports apart from RJ45 and USB, as I did not need access...

Raspberry Pi5 PCIe NVMe Case for Waveshare M.2 HAT+Update 21Nov24There was a small blemish discovered to the button recess.This has now been fixed.New STL and Step files have been added to downloads.These files are all annotated v28The round button...

I Stretched the case designed by Haz1 to make room for a POE Texas hat. Just a simple remix. It's pretty rough but does exactly whats needed. Thanks for the great work Haz1 find his original thing: https://www.thingiverse.com/thing:3724434 Poe hat:...

I Designed a Custom Case for Raspberry Pi 3B with HAT HifiBerry AMP2. This project is based on my previous design, which you can find here: https://www.thingiverse.com/thing:3325342. The power supply location has been relocated to make room for the...

I couldn't find a case that I liked for the MMDVM_HS_Dual_Hat so I designed one for the Raspberry Pi 4. STEP and STL files are included if you would like to make any modifications to the model. I assemble mine with 4x M2.5x22mm screws. These...

Parts List for tall case: 3D printed parts for the case: 1 x Top 1 x Bottom 2 x Speaker Retainers 4 x screws (M2.5 or M3, x 50mm) 4 x nuts (M2.5 or M3 depending on the screws) 2 x small screws for the speaker retainers Raspberry Pi 4 (any) - $59.99...

Rpi Dead Man Alarm (RDMA) Raspberry Pi Hat Case Case for rpi-dead-man-alarm Raspberry Pi hat Occupancy Monitor Use case: for a 24/7 control center with only one person on duty. Alerts people via SMS if the person on duty is unresponsive. ... Video of it...

... supports. (I let the Prusa Slicer 2.6 auto-paint the supports on the case.)Printed with PLA or PETG at 0.20mm QUALITY-Mode.Used M2.5 spacers and screws to mount the Raspberry Pi and MMDVM inside the case, and used M3 screws for the case itself.

To that end, I'm getting power from a spare 24V rail off the CR-6's PSU, using a LM2596 step-down module to output 5V, and a UPS hat with a small battery that triggers a graceful shutdown of the RPi when power is cut. Malolo's case was a fantastic...

... ...or at least I bought those. ... This is a simple case for a Raspberry Pi Zero (w), with all his ports still accessible and a additional space for the ePaper HAT by Waveshare.