clone prusa i3 mk3s 3d models

... plastic spacers between the extruder fan and heat sink. ...Print Settings: Printer Brand: RepRap Printer: Mendel I3 Rafts: Doesn't Matter Supports: No Notes: Designed to be printed in the same orientation as it will be installed, no support necessary.

... precise idler gear model after discovering that other models allowed too much play in the mechanism. ...This new design is specifically tailored to fit the X-axis end idler from the Prusa MK2 model, and I'm thoroughly satisfied with its performance.

The typical 8mm diameter inductive probe has such a small detection range and it's difficult and expensive to acquire Prusa's P.I.N.D.A. probe. The larger 18mm diameter probes have a much larger detection range so you can keep the probe a lot higher...

Unfortunately, it did not fit my i3 printer correctly. Attempting to modify the part using Autoscad proved unsuccessful as I was unable to add sufficient length to the design. The software failed to accurately create the part. I solely utilized the...

Other models that I found gave too much wiggle room for the idler gear, so I decided to model my own and I'm really happy with it. It's made for the X axis end idler from the prusa mk2 model. Print Settings Rafts: No Supports: Yes Infill: 40%...

The Geeetech I3 has a design flaw that causes extreme Z-axis wobble due to the top end of the Z screw being mounted solidly. This replacement shoulder piece leads the Z-screw, reducing wobble significantly by allowing it to move freely like a...

This Bowden setup is specifically designed for the CTC DIY I3 and includes two main components: - The part you are currently viewing - An extruder mount that can be found at https://www.thingiverse.com/thing:2942200 Alternatively, users can opt for...

Most of the printable parts are made from ABS material and were either Prusa MK3 or MK2 components. I modified the X-carriage to accommodate a BL-Touch type sensor, while the Z carriage parts were altered to match brass T8 nuts. I've included a...

For easier loading of filament, I remixed the Bondtech Prusa i3 MK2.5S / MK3S / MK3S+ extruder sensor cover to add a tapered tube for the filament loading hole.Print with PETG as oriented - no supports.Bondtech github part link ( Sensor Cover...

This is a Remix of the "Vertical LED Light Bars for the Prusa i3 MK3S/MK3S+" from Dennis. So please look into his work to get the holder for this bar. I used these profiles 17mm: LED Profile with covertogether with these led stripes: USB 5V LED...

[Japanese] PRUSA i3 MK2.5S/MK3S/MK3S+のホットエンドに挿入するPTFEチューブは両端を60度のベベルカットにしなくてはいけません。純正品を購入したりセンタードリル等を使って加工することが推奨されていますが、もっと手軽に製作できるように一般的なアートナイフ（OLFA 10B/10BS）を使ってカットと両端のトリムを行えるジグを作成しました。 MK3S+用（42.3mm） または...

This is a Remix of the "Vertical LED Light Bars for the Prusa i3 MK3S/MK3S+" from Dennis. So please look into his work to get the holder for this bar. I used these profiles 17mm: LED Profile with covertogether with these led stripes: USB 5V...

Simple combi tool (spacer holder and wrench) for quicker and easier application of the “Nylock Mod” on a Prusa I3 MK3S/MK3S+. One end of the tool can be used as a wrench to turn the nylock nuts. The other end contains an 6mm socket where you can...

... designed around the low profile ice cooler for Raspberry Pi 4B. ... Uses the screws and other hardware included with the low profile ice cooler. I used two M3x14b screws from my MK3S+ spares bag to attach it to the printer. ...There is barely enough

I wanted something easier to get on and off if I had to.That's when I came across FLink's light frame project (https://www.prusaprinters.org/prints/37475-led-frame-mk3s) which I considered to be slightly overkill for my needs but I liked his mounting...

Many of the guides I tried did not fit well on the frame, so I designed this one from several other designs. ...It is easily attached to the frame, but it is firmly attached!

This little extruder indicator was inspired by others with similar designs that didn't quite meet my needs, so I created my own. My design requirements included: indication needed to be unique over a 360° range, no repetitive pattern, which is really...

The new printer knob has been completely reimagined to address its predecessor's major flaws. Gone are the days of a bulky, conical shape that made it difficult for fingers to grasp, resulting in poor grip and frustrating use. ...This revamped design is...

Off set mount. Opens up hot end area so I can see what is happening with the print. Reduces interference with print. Require relocation of fan and removal of fan mount. Clean up print where extension seats into OEM holder. Used small channel...

I searched a while for a good solution to watch printing via Endoscope Camera, but did not find one working for me. So I decided to build one. The 8 mm Camera I used is a very cheap one from eBay...

<p>This little extruder indicator was inspired by others with a similar design. They did not fully meet my needs, so I made my own.</p> <p>My design specification included:</p> <ul> <li>indication needs to be unique over a 360° range, i.e. no...

I've been plagued by spools wobbling loose from my spool holder due to the limited width of the spool. To prevent this issue, I took matters into my own hands and designed custom spool holders with enlarged parts. ...These new holders feature 5mm, 10mm,...

<p>This is a multi size nozzle holder. I had purchased a pack on amazon and could not find a holder that held my range of size. I made one plain and one labeled for the mk3. ...Currently printing in .4mm nozzle but the size text might be a little...

My first "Thing", any advice is appreciated. Created on Prusaslicer, just a name tag. ...Color change half was through so the letters stand out.

Hello, Here is a diffuser design with eight symmetrically arranged openings facing hot end, for balanced cooling.

0.20 mm layer height0.4 mm nozzleMounting steps are the same as here: https://www.thingiverse.com/thing:4223581 - using the lock is optional.

Relocated fan for better hot end access. Need to remove fan housing nubs. Fit up required. Glue will keep fan in place. ... Allen key handles https://www.thingiverse.com/thing:980720 pinda relocation: ...

<p>Couldn't find a simple bracket to fit under cabinet led lights like the ones I had so I designed my own. Printed using PETG for extra flexibility on the clamp. Might work with PLA too.</p><p>The light bars can be mounted with M3x12 counter sunk...