clodbuster chassis 3d models

It will work with other clodbuster chassis as long as two conditions are met: 1) that the body mount spacing is the same as a stock clodbuster chassis side to side and front to rear - and - 2) that you are using the stock body mount pins as these...

I wanted to install my ESC at the bottom of the Clodbuster's chassis tub, so I tried moving it from its original position on top. However, the recesses for the battery box and receiver prevented the original top plate from fitting properly.\r\n\r\nTo...

Clodbuster Bumpers Loosely Based on My 5-Star Bumper Design (http://www.thingiverse.com/thing:2066905). This Thing is Currently Configured with a 12mm Hex Hub for Enhanced Performance. Print Settings: Printer Brand: FlashForge Printer Model:...

axle tube for Tamiya Clodbuster

... Stp files included for remix. Based on Drommond design from his Clodbuster and Axial chassis on Thingiverse. I just simplified them to lighten each wheel 50-60g. ...One piece wheel can be printed with minimal support as seen in last photo.</p>

Here we have blanks for the 2 switch holes in the Clodbuster or Bullhead chassis, useful to tidy up the appearance of a lightly modified truck. ... <iframe width="560" height="315" src="https://www.youtube.com/embed/TKORF2-1nVI" frameborder="0"...

If you're relocating the battery these blanks neatly cover up the big holes in the chassis and provide mounts for on/off switches. ... <iframe width="560" height="315" src="https://www.youtube.com/embed/TKORF2-1nVI" frameborder="0"...

Replacement Hood Scoop Upgrade Kit for Tamiya 1/10 Scale Clodbuster Remote Control Off-Road Truck.

I printed the chassis and wheels that Matt designed for use with Clodbuster axles and tires found here. https://www.thingiverse.com/thing:3347976 While I am completely stoked with the overall build I felt that the center of the wheel was missing...

Clodbuster body panel what comes in the front, under the grill. ...Design is not ideal, but works ok.

These mounts are designed almost exactly as the original rear body mounts for the Tamiya Clodbuster stock truck. ...

The stand locates on the central section of the chassis and follows the contours of the trucks mouldings. It needs no support material and quite an easy print. I printed in PETG but PLA will also be fine. My intention was to make the stand look...

Since the chassis is the same on both sides, a left rear chassis section can also be used as a right front chassis section. If you have any questions just ask and I'll try to respond as soon as possible while I get around to writing up a better guide...

I printed the chassis and wheels that Matt designed for use with Clodbuster axles and tires found here. https://www.thingiverse.com/thing:3347976 While I am completely stoked with the overall build I felt that the center of the wheel was missing...

The new design adheres to Clodbuster, Super Clodbuster, and Bullhead requirements. Here are the simple installation guidelines: Simply replace the stock component with this custom upgrade! ... If your transmission housings still bear the locating...

I recently acquired my first Clodbuster and was motivated to start crafting custom parts for it. The initial component I required was a differential locker for the rear axle, so I designed one based on an existing model that had been removed from...

Rear steering lock out plate for the Clodbuster. You can run it as shown or flip the knuckles side to side and run it lower. I like the way shown because it has better ground clearance. ...Printed at 100% infill at 215C.

You're going to need two of these pieces to lock one differential on your Clodbuster. It's best to just lock the rear diff if you drive like a monster truck, because that's how the Clod was meant to be driven! ...:) First, set up your print settings: ...

Tamiya Clodbuster/Bullhead Counter Gear - 44T/15T printed using 9999 bottom layers used PLA and its been holding up on my rig for a bit. I don't have a brushless system nor do I bash it hard so it works for me. ... Maybe use PETG or ABS or Carbon...

I designed this custom tray to securely hold a 2200mAh LiPo battery in the original battery compartment of my Clodbuster. ...The tray provides a precise fit for my Turnigy batteries, giving them a snug and secure place to rest.\r\n\r\nThis solution...

I crafted my own version of a center axle servo mount for the Clodbuster that would complement the truck's appearance while preserving its stock bumper look. ...The lower tube I sourced from Hot Racing for about five bucks is 53mm in diameter, and I'm...

First thing I uploaded was a steering knuckle for my Clodbuster. I started renovating my trusty 25+ year old Clod and discovered that steering knuckles are difficult to find and pricey. It's not an exact replica of the original, I moved the steering...

This is a protector for a ARCH Fabrication and Machine Aluminum servo mount / bumper for a Clodbuster. I believe this will only work if you have the servo mounted up high (not using the spacers that come with the bumper). If you would like me to...

Printed at 100% infill at 215C. Print instructionsCategory: 3D Printing Summary Rear steering lock out plate for the Clodbuster. You can run it as shown or flip the knuckles side to side and run it lower. I like the way shown because it has better...

Tamiya Clodbuster GMC Grille. Included are all the files to print a complete grille assembly. I would recommend printing these items on a Resin MSLA printer due to very fine details in the parts. I cannot confirm all the parts will fit...

This Thing upgrades the old wobbly steering on the ClodBuster and Bullhead to a far more stable setup. Th plan with this upgrade was to try and keep it looking fairly stock from a distance, but still have the best possible steering. The mount fits...

Same thing as Drommon's, I just added spacers to drop the servo down so it doesn't hit the chassis so soon, and a 53mm tube until you can order the aluminum one from Hot Racing. ...This is by far my favorite mount.

Tamiya's iconic Clodbuster 1/10 scale RC truck boasts impressive off-road capabilities, thanks in part to its rugged roll bar support system.

Here we have a replacement electronics tray for the Tamiya Clodbuster and Bullhead. It's designed to take 2 Tamiya TBLE-02S ESCs and a FlySky 6 or 8 channel receiver. There's also a flat version so you can mount any brand you like. ... Battery:...

I'm still refining this design. ...A higher mounting point for the upper link of my Clod Buster project is necessary; this setup seems promising, but I'm uncertain whether it'll align perfectly with the stock chassis without extending the wheelbase.