clock from loki 3d models

I did adjust the support placement angle to cover from the build plate to the bottom areas of each part. Then added support blockers if supports hit the front face of the parts. I printed all with a brim to ensure good bed adhesion and turned off the...

Those two parts are also included without supports for those makers who prefer to use supports via their slicer. If you have the proper filament colors, no painting is needed. The assembled model is 230mm tall. Enjoy Note: the built-in supports...

This could be avoid if you know, and want, to drive directly the stepper coils.Anything that could generate a square signal (if you use the driver), from a 555 chip, to a microcontroller board (like an Arduino, or in my case the EDU-CIAA board). ####...

Best of all, this works with most printers, because you simply have to change filament at certain heights. I took extra care and designed it in such a way that you don't need any special tools or components, just a bit of wire and spring from an old...

as you can see from the pictures, the scarf is printed flat on the plate yet it has a knot and hangs down on the finished snowman. I made it flat so I could print layers of different colors and shape it after printing it. This is accomplished by...

I have the Pi and mainboard raised 10mm from the base so that you can route cables underneath them for a cleaner look and better cooling. I would also get your fans installed at this point and create whatever type of connections/connectors you need...

This results in a much cleaner final print, and since no support structures are require and flat parts generally print faster than tall parts, it also reduced my print time from nearly 7 hours for the full model, down to about 2 hours for the...

The first is ready for motion switch and the second one is without any holes for switch (you can have the switch straight in power adapter or you can put the switch to the aluminium profile- infra red switch or touch switch). You will...

You don't need the touch screen for this project. Zero Delay USB encoder - this also comes with the cables needed. Nuts & Bolts: + 26x M3 nuts + 24x M3x12 bolts (You can use longer bolts for most connections) + 2x M3x18 bolts (Longer are fine...

... screw (M3X20) with locking nut. Be very careful not to cut ESCs cables while you thread the bolt. Push a thin rod to clear the way from the cables before threading the bolt. ... Now do this 3 more times (if you are flying a quad) and you are golden.

V1.7: Removed F3D file from zip downloadable - file size is now down two-thirds and it plays nice with Thingiverse not making buggy downloads. Relocated being able to edit the file to a public link instead. V1.8: Revised designs for the 'Upper' to be...

Here is my reload to the X-axis mod from "patsp" https://www.thingiverse.com/thing:4597994 The author had already made improvements in version 2 and the lower part - well Nozzel height caught again with a roller to avoid any distortion due to...

None of these parts should cost much more than $2 each if you are willing to wait for shipping from China. I think I have $10-12 in this in parts (don't ask how long I spent designing it) and the power supply was sitting in my junk box with a broken...

- Add the two support rods, being careful to make sure that the screw heads do not protrude from the support, as this will touch the wall of the box (Photo 1). - Pre-drill and screw a screw on each side of the removable spool holder (there is a...

Its power supply can range from 4V to 24V, although the most commonly used voltage is 5V. A drawing is also included with the timing results for a burst of 5 balls. It's essential to note that sometimes the speed can be quite high (pulses about 25...

This will prevent the sides of the wing from contacting the case. (4) Insert switches and keycaps into plate and PCB. (5) Clip the gasket wings onto the plate (not the PCB) so that they line up with the gasket wells in the case. (6) Once...

You can also pull a hatch emblem from the parts yard.This model conveniently uses the same OEM mounting points. It's also beefier, more secure, and optimized for 3D printing.</p><p>Attach the optional slide lock and slide to towards the front after...

Mini-reels all but disappeared from the market.While mini-reels may not be commercially viable, there is still a use-case for them. The fact that several distributors offer a "re-reeling service" proves that there is still a market for buying smaller...

Their purpose is to prevent the tray from sliding when placed on top of the lid, both when in play and when storing multiple stacked trays in between sessions. * Optionally, one each of the small and large card dividers. They are intended to separate...

The naming of these variants might change without notice, so again, pay attention to the pictures and read some reviews.If after all this effort, a GPU still doesn't fit underneath the HDD, I have a gut feeling that taking some time to sand down the...

https://www.amazon.ca/gp/product/B06XMQG4TC/ref=ppx_yo_dt_b_asin_title_o07_s00?ie=UTF8&psc=1 10) 4x Rotary Push button encoders (these come with buttons, but I opted to order the aluminum ones from Aliexpress, see item #4). 12) You will need a...

Of course, I've also included a separate file that separates the support from the main body. This is useful for those who want to push their printer to its limits or modify it to suit their needs. Throughout the design process, I used Onshape's...

Message us for a quote Realistic low-poly vegetation — individual trees in max and fbx formats, additional formats upon request before you pay Product is ready to render out-of-the-box — 3ds Max + Corona Render PRESENTATION IMAGES 4K high-resolution...

This will prevent the sides of the wing from contacting the case. (4) Insert switches and keycaps into plate and PCB. (5) Clip the gasket wings onto the plate (not the PCB) so that they line up with the gasket wells in the case. (6) Once clipped into...

Input voltage can range from 12-40v depending on what power supply is easier for you to obtain. Modelled rear inputs consist of 2x DC Jacks (for redundancy or daisy-chaining), Ethernet Jack and a GX16 Aviation Connector (for general purpose or...

All of the parts can be sourced for around $75-100 depending on where you buy from. In addition to the parts and hardware, at least .3 kilograms of strong filament is required. ASA/ABS is likely the preffered option for rigidity. Here is the list...

This can be done with: PrusaSlicer using color change Cura using: Extensions &gt; Post processing &gt; Modify G-code &gt; Add a script &gt; filament change Prusa's ColorPrint webapp ("G-code is supported from Slic3r, Cura, KISSlicer and...

(This was a user request I'm not sure about stability of this model and I have not printed it, use at your own risk)   Update 5/1/2017: Added power led indicator and front bevel to switch docking area, rebuilt 3D model from scratch with better...

My changes were some improvements: I utilized the V-Slot of our printers, so that the motor holder and the nut holder now fit the slot and therefore are attached even more stably (important especially for the motor holder, which will experience...

It is still a very desirable piece of beloved retro tech to this day!This mini-monitor design was modeled in 3DSMax for 3D printing to use with an 8 inch LCD Monitor 4:3 IPS (1024x768) Screen, and incorporates inputs for HDMI, VGA, AV, BNC Built-in...