clever useful 3d prints

Only Makers with well-Calibrated 3d printers will be able to print this so if that's you take the challenge!! If you have an questions or concerns or you need anything to be modified please let me know, in the comments or send me a message! I love...

Note: Depending on your 3d printing setup you still may have to cut off a little bit the top of the bottom part spheres, too much pressure can still brake the hinges. ... ORIGINAL DESING: TheSameNameTwice AA Box:...

Individuals employ a 3D printer to fabricate test components utilizing the JBarbosa M3DCF system.

Print settings include 1% infill, .3mm layer height, one shell, a feed rate of 60 mm/s, and using raft/support with no additional support. ...The platform temperature should be set at 120 degrees C, while the extruder temperature is set to 225 degrees...

I was going to make some cute foot prints for the elf but I noticed that our elf just has round feet.... ...and my daughter would notice details like that.Ihis is be be used with flour or sugar to make foot prints

Project Details: Material: PLA Printing Temperature: 200 C Bed Temperature: 60 C Layer Height: 0.2 mm Infill Density: 50% No support required For more information and to watch this video in its entirety, visit my YouTube channel at...

The modern semaphore flag system is now being translated into printable designs for 3D multi-color printing. Additional MCP semaphores are on the way. ... Please let us know if you have any modifications or commercial inquiries: tom-harder-sec@web.de

This is an updated version of my older design: https://www.thingiverse.com/thing:1997800 This new design boasts enhanced robustness and solidity when printed in PLA, with successful results achieved using both transparent and Black PLA filaments. I'd...

I was looking for something that did all of the following: -Printed in Vase Modem (Spiralize Outer Contour) -Had a threaded Lid -Fits in the center of a kg spool My Settings for Jar: -Use Vase Mode or Spiralize Outer Shell mode. -Set bottom...

You can read more about this process at https://wordpress.com/post/78513574/78 **Reusing Print Pieces** If your print reaches the halfway mark, you can use a sharp chisel to smooth out top and bottom faces so they are flat. Put pin clips into the...

... in a 100% success rate for small prints so far. When printing these tiny models, use a decent amount of infill (I've used 75%, but you might get away with less). ...Once the print is complete, drill a small hole at the top and attach your keychain.

I use the jar greenhouse with the extra large Nutella jars (750g), the biggest jar I found in our household - thanks to my kids ;-) For using these Nutella-jars I printed in 102,5% scale. I added a third circle of "pillars" (see photo in printing)...

I use the jar greenhouse with the extra large Nutella jars (750g), the biggest jar I found in our household - thanks to my kids ;-) For using these Nutella-jars I printed in 102,5% scale. I added a third circle of "pillars" (see photo in printing)...

Prints with no support.

* **RuneWars - Base 1-4**: Print each of these pieces and use super glue to glue them together. These need to be assembled in order clockwise 1-2-3-4 so that the tiles will fit properly. * **RuneWars - Cards 1-2**: This is a modified version of the...

https://www.youtube.com/watch?v=akXrIWGhpfE **Print and Assemble Your Balalaika** Infill Settings: - Print the body at 50% infill with around 5 perimeters (shell). - Print the neck at 50% or higher to achieve a stable vertical structure. - The...

This design enables you to print and install a D-Link camera on your printer, allowing real-time monitoring of the printing process from any location. To begin, obtain a D-Link camera; we specifically designed this model for use with the DCS-930L.

... 6 chairs. (From reviewing the failed parts I think they are likely failing due to high line contact stress that happens to align with the knit line of the molding, directly opposite the gate on the part. This 3D printed part resolves the issue.)

Just an empty frame to create art like this: https://www.prusaprinters.org/prints/122835-levi-wall-art-framedhttps://www.prusaprinters.org/prints/123297-mikasa-from-attach-on-titan-frameJust import into your design tool(I just used tinkercad),...

... I was facing and thus far I have achieved a 100% success rate for tiny prints! Just print with sufficient infill (I've used 75% but believe you can get away with less), then once it's printed drill a small opening at the top and attach the keyring!

The Printrbot Simple printer I use has a 10cmx10cmx10cm print volume. ...Since it couldn't handle the entire job in one pass, I broke it down into two prints.\nPrinting different colors can be done with ease, I split the gear types for this...

Spade - Infil to add weight, no supports Letters - Print flat, already scaled to fit nicely in the embossing Star - Infil to add weight. Full print with 4x4x4 walls/top/bottom and 38% infil came to about 48g in weight. Glue in lettering and...

Also includes a version with cubic segments, and two example customizations: a simple cat, and the famous #3DBenchy Please check your extrusion ratio before printing to avoid fusing the hinges into the rest of the print. If you wish to do a filament...

but again, it prints so quick and uses so little filament that it doesn't really matter. Two tips: After removing from the build plate – re-heat the build plate with the barrettes on the build surface to heat them up. Then, when they are warm, bend...

Relying on the flexibility offered by printed faces, various instrumentation configurations become a reality. ...To implement this setup, simply print the instrument face onto heavyweight paper and securely attach it between two components of the gauge.

I printed the Curing Station Feet in Ninjaflex TPU, but you can use PLA or whatever you like as well. Bill of Materials: Aside from the "Curing Station Feet", print 1 of each file. Print 4X - Curing Station Feet 1X - Solar Powered Turntable:...

Add a sheet of transparency, a binder cover, or a plastic sheet protector - or possibly use two-liter bottle plastic that's been trimmed. This design prints on an approximate 6x8 printer bed. ...I've corrected the one hook misalignment issue - sorry...

... never have to worry about stretching the filament or experiencing low feed rates in your extruder. The holder prints out 1 part with support and 4 parts without. I created it specifically for use with my own TPU filament at Rubber3DPrinting.com.

A easy print and add to your used PET bottle and water your plants. Update 3/19/2022:  Added file with brim for those having bed adhesion issues.Update 3/22/2022: Added file with brim and spike with only one hole.

Knowing this design will limit the height of my prints as the extruder cables can interfere with the filament spool. ...Meant to be custom and particular for my enclosure setup but if this is useful for someone else out there, here are the files.