claymore mines 3d models

I've got connector plugs in mine near the gantry which is easy and also looks like hot garbage...Print SettingsPrinter:Sovol SV-01Rafts:NoSupports:YesResolution:200Infill:40 - GyroidFilament:  ABSNotes:See Cura screenshots for best orientation. Also...

Obviously, you will also need to buy an electric cable including a connector (I bought mine at "Clas Ohlson" in Sweden). You must ENSURE not to overheat the printed parts so take good care of which lamps to use. Personally, I use LED lamps of no more...

Every design just named *centrifugal pump* (like mine) doesnt help much. After some research i found two numbers to rate pumps: 1. The head they produce. Its just the height the pump can push water upwards. 2. The flowrate, thats the amount of...

One part of the railway was the coal (lignite) and briquette transport from nearby mines to the town to feed the steam engines mainly in cloth factories. There were about 70 of these wagons and trains could carry up to 15 to 20 wagons according the...

I thought the frame came with this, but mine did not. * needs supports * 16% infill * **Vista_Antenna_Mount_FPVCycle_Fouride.stl** * Rear Vista antenna mount for the fouride. shorter in height than the one for the prototype this may...

Thanks CFox! This is the new file:internal-608-roller-bearing-base-adapter-for-newer-printers-1.0.stlI've you're using an older printer like mine in the pictures, print this...

Mine was slightly, so I just glued a small piece of angle iron to the back of it to straighten it up. If you don’t do this, then your pump positions will be slightly off and propagation of errors will become an issue later 8. Insert the Oxidizer and...

Mine didn't came out great because of that, but yours can. - A printer that doesn't wobble/vibrate (tall structures may suffer from vibration, particularly the spine which needs to be somewhat straight and thin) ## Print orientations Case...

I use a 5 minute 2-part epoxy from any hardware store (I get mine from Harbor Freight since its super cheap and works the same as any other brand). Start with gluing together the 2 middle pieces, ‘Middle Bottom’ and ‘Middle Top’. It's at this point...

For a wiring diagram please refer to the images for how mine is setup as an example.   BOM 1x Battery Display : https://www.amazon.co.uk/dp/B07DVSTY59 4x M5 70mm Bolts : https://www.amazon.co.uk/dp/B07X8Q73SK 4x M5 Serrated Flange Nuts...

This light is designed for heavy duty use in demanding conditions including emergency services, mining, construction, marine, and industrial operations where durability and reliability is critical.This portable LED light is comprised of two...

Mine just needed the supports to be removed and worked fine. To start, install the M3 nuts into the base, there are 10 pockets (see 1st pic) and I added a small drop of glue (clear Gorilla Glue) to each pocket, then pushed the M3 nut into the pocket...

…the corner pieces didn't print nicely enough for mine to perfectly assemble. (maybe that's my tuning issue, orientation, or lack of supports)--------------------everything below this line is copied from original that this is a remix of- full credit...

This is also an indication for printing these parts in an accent color (mine was orange).STL naming an meanings:[a]: accent color (means middle section of the pro version, mine was orange)x2: you have to print the part 2 times (example)IL1: parts for...

... <h3>Final note</h3> <p>I would insulate the spring clips in the power track if there was any chance of shorts. Mine are mounted on wood. I haven't found a source for spring clips other than extracting them from a breadboard.

For example, mine had red, black, and green wires (which are used for 3.3v, ground, and signal respectively).Step 5Test the endstop with the board plugged into your Octoprint board. If the LED is ON before you insert the filament, the metal switch...

The housing is specially designed to dissipate heat which increases the efficiency and lifespan of the LEDs and electronics.Suggested Applications: The EPL-HB-150LED-RT-180B is approved for use within environments where flammable or combustible...

and i use autohotkey as an app launcher for LeftCtrl, Alt, Win + a letter (a through j) Unzip the UltiPad.zip into your QMK folder in your build env, and modify/compile your own keymap. Let me know how you make out! Edit, added a slightly shortened...

You may need to adjust the `centerColumnHeight` variable and re-build that object if your existing center column doesn't match mine. If you go this route, you'll need to lock the bottom reel to the 3D-printed central column, and lock each additional...

Mine had somehow drifted over time due to loose screws, because of which I wasted some time in understanding why my X carriage didn't move freely and was wobbling a bit. After meticulously squaring the frame, the problem was resolved. **Mandatory...

The original effector is 6mm's thick, mine is 7. The rod end mounts are 52 mm's wide. So are my carriages. This way I don't need the spacers. This worked well for me for years, then I got the itch for dual extruders. I designed an effector that will...

Plug options include a 5-15 15 amp straight blade plug for use with 120V explosion proof outlets, a 5-20 20 amp straight blade plug for use with 120V explosion proof outlets, or a 6-20 20 amp straight blade plug for use with 220-240V explosion proof...

If they are too loose, you can glue them in with CA glue.The gears need to spin freely on the metal shafts, mine worked fine right off the printer. You can drill them out with an 1/16" drill bit if needed (use the included drilling jig to make sure...

For example, mine had red, black, and green wires (which are used for 3.3v, ground, and signal respectively).Step 5Test the endstop with the board plugged into your Octoprint board. If the LED is ON before you insert the filament, the metal switch...

However, if your tripod isn't very good (mine aren't) I'd suggest setting the camera to use electronic shutter and either remotely trigger it or use the selt timer -- that will minimize misalignments due to vibration -- and also brace the tripod...

I have provided a 3mf project so you can see how I printed mine. You certainly don't need all these files that I've provided but maybe they help some people or maybe you give me feedback on the settings I'm using and we all learn. The Bed...

I do appreciate Seth's support and input during this process, but the designs of the coins (and any failures thereof) are mine. No resale allowed but free sharing and further modification is encouraged.</p><p>These coins are intended to follow the...

&nbsp;I have mine in the front, with a USB fan in the back, but the opposite would also work fine. &nbsp;Which is best may depend on which direction you tend to feed filament. &nbsp;I don't hit any issues feeding filament under the bottom, past the...

I got mine off digikey (https://www.digikey.com/en/products/detail/bourns-inc/PDB181-K220K-103B/3780701 or https://www.digikey.com/en/products/detail/tt-electronics-bi/P164K101PNN20B103/12162423) The manual range knob I just used a normal rotary...

Mine has traveled a bit and remains intact, but you may want to just epoxy some wire and a bead.Should you choose to embark on the printed version:Print 2. It's labeled "left," but both sides are the same</li><li>Use a fine layer height. (As low as...