claymore mine 3d models

This made mine work perfectly. Do this before placing the bearings in the bore, and do it with gloves on! The end mill caught me by surprise and drew blood.</p><h3>Print instructions</h3><p>I made the body in PETG, .2mm layer height, 3 perimeters,...

I have mine in an enclosure and only have them printed in PETG instead of ABS or stronger. So I have experienced some issues over time with these due to the heat. I changed the slots used for mounting to the linear guide block to holes and beefed...

... if you get that far before I do and I'll update it here. Also, thanks to Tximy. Hole sizing and spacing from this design for the wheels/Eccentric nut saved me from having to fully dismantle mine. ... https://www.thingiverse.com/thing:3343882

You can Help me helping MyRCCar of course, as I feel it until now like a child of mine ;) Showing my projects and giving attribution is in the end the best you can do for me to help me find a good job. But If you think it would be nice I would go on...

However, if your tripod isn't very good (mine aren't) I'd suggest setting the camera to use electronic shutter and either remotely trigger it or use the selt timer -- that will minimize misalignments due to vibration -- and also brace the tripod...

Obviously, you will also need to buy an electric cable including a connector (I bought mine at "Clas Ohlson" in Sweden). You must ENSURE not to overheat the printed parts so take good care of which lamps to use. Personally, I use LED lamps of no more...

Thanks CFox!&nbsp;This is the new file:internal-608-roller-bearing-base-adapter-for-newer-printers-1.0.stlI've you're using an older printer like mine in the pictures, print this...

I use a 5 minute 2-part epoxy from any hardware store (I get mine from Harbor Freight since its super cheap and works the same as any other brand). Start with gluing together the 2 middle pieces, ‘Middle Bottom’ and ‘Middle Top’. It's at this point...

I got mine off digikey (https://www.digikey.com/en/products/detail/bourns-inc/PDB181-K220K-103B/3780701 or https://www.digikey.com/en/products/detail/tt-electronics-bi/P164K101PNN20B103/12162423) The manual range knob I just used a normal rotary...

I didn't bother installing it for mine. Brass rather than steel is a good choice to avoid scratching your camera's mount surface.</p><figure class="image"><img...

The housing is specially designed to dissipate heat which increases the efficiency and lifespan of the LEDs and electronics.Suggested Applications: The EPL-HB-150LED-RT-C is approved for use within environments where flammable or combustible gases,...

I got mine from https://3dprintingcanada.com/collections/tpe/products/black-1-75mm-tpe-filament-0-5-kg (not affiliated). Video: - In action: https://youtu.be/3EBpf9YP5C4 - Showing the shock: https://youtu.be/YSYngEb9dG8 - Gearbox assembly:...

Update 2 (2018-02-24): I've been musing about the z&gt;160mm problem for chains that don't coil perfectly like mine (see update 1 above). I considered several approaches, but ended up with the most simple one: a fence which keeps the chain from...

They can be mounted with stock components, or with another work of mine, the "anti Z wobble" inspired by HEVORT (I put the link at the bottom of the article). The attachments are fixed to the aluminum profile of the X axis with 4 M5 12mm screws and 4...

Plug options include a 5-15 15 amp straight blade plug for use with 120V explosion proof outlets, a 5-20 20 amp straight blade plug for use with 120V explosion proof outlets, or a 6-20 20 amp straight blade plug for use with 220-240V explosion proof...

I think mine were roughly 9 inches/22 cm; longer is easier to work withCut a small length of aluminum wire and wrap around the center (this is just to hold everything together temporarilyCut another length of the black nylon thread, exact length...

The housing is specially designed to dissipate heat which increases the efficiency and lifespan of the LEDs and electronics.Suggested Applications: The EPL-HB-150LED-RT-180B is approved for use within environments where flammable or combustible...

... <h3>Final note</h3> <p>I would insulate the spring clips in the power track if there was any chance of shorts. Mine are mounted on wood. I haven't found a source for spring clips other than extracting them from a breadboard.

The housing is specially designed to dissipate heat which increases the efficiency and lifespan of the LEDs and electronics.Suggested Applications: The EPL-IBM-FA-3X150LED-RT is approved for use within environments where flammable or combustible...

The housing is specially designed to dissipate heat which increases the efficiency and lifespan of the LEDs and electronics.Suggested Applications: The EPL-HB-150LED-RT is approved for use within environments where flammable or combustible gases,...

This light is designed for heavy duty use in demanding conditions including emergency services, mining, construction, marine, and industrial operations where durability and reliability is critical.This portable LED light is comprised of an adjustable...

When you don't use an exhaust system like mine, this is how 99%+ of the fumes enter your work area. The cover is pretty well sealed, very little fumes will escape from there. Also when the the two cooling fans are on, (along with the exhaust fan...

Cam mechanisms are usually used to convert rotary motion into linear motion, but can be used for the inverse purpose just as well.Required3D Printer - accommodating a build size of at least 210x80mmFilament: no specific requirements I used mainly...

All other mods (uprights, tensioners, fan duckt) you can see on screen are not mine, but i can link them if there is enough interest. WARNING!!! THIS IS NOT A SIMPLE PROJECT! DISASSEMBLE YOUR PRINTER AT YOUR OWN RISK! I AM NOT RESPONSIBLE FOR...

Mine just needed the supports to be removed and worked fine. To start, install the M3 nuts into the base, there are 10 pockets (see 1st pic) and I added a small drop of glue (clear Gorilla Glue) to each pocket, then pushed the M3 nut into the pocket...

&nbsp;I have mine in the front, with a USB fan in the back, but the opposite would also work fine. &nbsp;Which is best may depend on which direction you tend to feed filament. &nbsp;I don't hit any issues feeding filament under the bottom, past the...

- if there is a fit issue (I had to change the dimension thickness of the chassis) hot water bend these to fit but mine fit perfect Lower box and rod - No support needed - 20 minute print - free mount for the base of the box, the rod will connect to...

  If you cannot get the wire installed, STOP and investigate the print, since it should not take a great amount of force to install the wires, and you may have an issue with the print which is blocking the holes for the wire hinge.  Do not push too...

... gone well and you have a piece of furniture of which you can be justly proud.   I am certainly very happy with mine!There is a lot of documentation here, and I'd really appreciate any feedback on anything that's not clear or in need of correction.

No special settings except for the optional color change.I suggest setting also the infill and supports angles to 35 degrees so it matches the angle of the parts.If you also want to print the letters on the cover you can use the MMU2 (or equivalent...