classic poker chip 3d models

This is a simple poker chip with a lithophane center. The files are the outer ring of the chip. I've included rings with the word "King", "Queen", "Ace" and "Joker". I've also included a blank ring in case you'd like to add your own text. Printing...

Eight row chip holder for 40mm chips.PLANo raftNo supportFour row chip holder for 40mm chips with handle.PLANo raftSupport for top knob

The tube stores 20 chips

Since they won't be visible while the tube is closed, you will be able to easily randomize seating for tournaments if you put players' starting stacks into such tubes. The measurements of the tube assume that you are storing high-quality...

I required poker chips that could be effortlessly embossed (both positive and negative embossing) for an event I was assisting with. Based on sethmoser's original design for the initial suits around the rim, I resliced repeatedly to achieve a...

Instructions Using the following options: Chip Font Name = Write/Letters Chip Value Height = 5 points Chip Diameter = 40 mm Value Font Name = Orbitron Value Name Thickness = 5 Casino Logo Size = 185 pixels Thickness of Chip = 5 mm

Hold 39mm&43mm chips in place before clamping

It has the same size as a standard Poker chips so it should easily fit together in a case with your set.You can print either the 4-colour or 2-colour version. Printing the 4-colour version is a bit more tricky, but the result is outstanding.Check out...

play poker reasonablyyou do have to change to a gcode file with curaslicer or another program

For every participant, assign a magnet to their chip, typically a small piece that contains iron.

Remixed the Chip Caddy by jbcantrell to be just the tray without the cup holder. ...

Tray that holds 5 rows of 20 standard size chips

This is an enhanced version of the Poker Trophy designed by llalonde. The text has been extracted from its original position to allow for flexibility in use. ...To create a larger trophy, I scaled up the design to 250%.

Instructions To create your custom chip, choose from the options below: Diameter: Select a diameter for your chip between 30 and 70. Thickness: Choose a thickness for your chip between 1.5 and 6. Font Name: Choose a font for your text using our...

... of thing:107494, created with Customizer! ... Instructions Using the following settings: Casino Font Name: Write Letters, from file: Lettres.dxf Chip Value: Casino Name Height: 10 units high Value Font Name: Write Letters, from file: Lettres.dxf

To utilize the model found at http://www.thingiverse.com/thing:79966, it is perfect for creating a dealer chip. This was an excellent task! ...Keep the tasks coming!

https://www.thingiverse.com/apps/customizer/run?thing_id=107494 Instructions Using the following options: Value font name: Write Letters.dxf Casino Font Name: Write Letters.dxf Thickness: 3 point five mm Diameter: forty millimeters Chip Value: I...

Https://www.thingiverse.com/apps/customizer/run?thing_id=107494 Instructions Using The Following Options: Casino Font Name = Orbitron Dxf File Diameter = Forty Casino Name Height = Four Width = One Hundred Seventy Five Casino Name = Groningen Poker...

http://www.thingiverse.com/apps/customizer/run?thing_id=107494 Instructions Using the following options: CasinoNameHeight = 7.1 ValuefontName = write/Letters.dxf ValueHeight = 12 width = 175 Thickness = 3.5 Diameter = 40 CasinofontName =...

http://www.thingiverse.com/apps/customizer/run?thing_id=107494 Instructions Using the following options: ValuefontName = write/Letters.dxf width = 175 Diameter = 40 CasinofontName = write/Letters.dxf CasinoName = Monroe Poker Thickness = 3.5...

http://www.thingiverse.com/apps/customizer/run?thing_id=107494 Instructions Using the following options: ValueHeight = 12 Thickness = 3.5 ValuefontName = write/Letters.dxf Diameter = 40 width = 175 CasinoName = Monroe Poker CasinofontName =...

For specific instructions, use these parameters: Diameter = 40, ValuefontName = write/Letters.dxf, ChipValue = 1000, width = 175, Thickness = 3.5, CasinoName = Christian Poker, CasinofontName = write/knewave.dxf, CasinoNameHeight = 7, and ValueHeight...

http://www.thingiverse.com/apps/customizer/run?thing_id=107494 Instructions Using the following options: ValuefontName = write/Letters.dxf width = 175 Diameter = 40 CasinofontName = write/Letters.dxf CasinoName = Monroe Poker Thickness = 3.5...

http://www.thingiverse.com/apps/customizer/run?thing_id=107494 Instructions Using the following options: CasinofontName = write/Letters.dxf Diameter = 40 width = 175 CasinoName = Tave's Poker Club CasinoNameHeight = 7.1 ValueHeight = 12 Thickness =...

http://www.thingiverse.com/apps/customizer/run?thing_id=107494 Instructions Using the following options: CasinoNameHeight = 7.1 ValuefontName = write/Letters.dxf ValueHeight = 12 width = 175 Thickness = 3.5 Diameter = 40 CasinofontName =...

Set the desired diameter of your casino chip to 40. 3. Adjust the height of the casino name to 7.1 with "CasinoNameHeight". 4. Input the chip value as 1000 under "ChipValue". 5. Enter "SETAR N.V" as your casino name using "CasinoName". 6. Set the...

... Height" of 7mm, "Casino Name Height" of 7.1mm, a diameter of 40mm and thickness of 3.5mm. The "Casino Name" and "Chip Value" (e.g., Dealer) can be customized, while the font for "Chip Value" is also set to "write/Letters.dxf" with a width of 175mm.

http://www.thingiverse.com/apps/customizer/run?thing_id=107494 You can use the following specifications: * Width is set at 175 units * Thickness comes in at 3.5 units * The diameter is established as 40 units In addition, a font file called...

The font used for the value is "write/Letters.dxf", while the chip thickness is 3.5mm and has a diameter of 40mm. The width is 175mm. For the casino-related elements, the font used is again "write/Letters.dxf". ...The casino name is "first" with a...

To create it, use the following options: CasinofontName set to 'write/Letters.dxf', ChipValue at 'x/1', CasinoName as 'Sky Trail Poker', thickness of 3.5, CasinoNameHeight of 5, a width of 175, ValuefontName also set to 'write/Letters.dxf', Diameter...