clarky 3d models
13 3d models found related to clarky.
myminifactory
Available sizes Small – 1:35 of the actual size | Normal & Pre-supported versions Medium – 1:10 of the actual size | Normal, Pre-supported and Hollowed versions Description Simosuchus clarki is an extinct crocodyliform reptile that lived during the...
myminifactory
Available sizes Small – 1:35 of the actual size | Normal & Pre-supported versions Medium – 1:10 of the actual size | Normal, Pre-supported and Hollowed versions Description Simosuchus clarki is an extinct crocodyliform reptile that lived during the...
sketchfab
State, County: WY, Natrona This specimen was discovered on federally managed land overseen by the Bureau of Land Management (BLM) Taxonomy: Reptilia>Thecodontia>Rauisuchidae>Heptasuchus clarki Heptasuchus clarki represented a species of pseudosuchian...
myminifactory
Available sizes Small – 1:35 of the actual size | Normal & Pre-supported versions Medium – 1:10 of the actual size | Normal, Pre-supported and Hollowed versions Description Simosuchus clarki is an extinct crocodyliform reptile that lived during the...
thingiverse
http://airfoiltools.com/airfoil/details?airfoil=clarky-il The hull should be 3D printed and covered with fiberglass or another form of reinforcement. Note that the interlocks in the hull are not designed to support the entire structure, so...
thingiverse
www.Thingiverse.com/apps/customizer/run?Thing_id=834725 Instructions Using the Following Options: Rotation = 50 Degrees Loop_x_position = -66 Units Loop_y_position = 0 Units Height = [5,6,4,5,4,3,5,4,6] Units Font_name = Chewy Font Spacing =...
thingiverse
profile ClarkY-12% (propeller.stl) The first launch and a short test of a propeller for an aircraft model printed on a 3D printer is shown in the video below. <iframe width="560" height="315" src="https://www.youtube.com/embed/mb92SwlWsJQ"...
cults3d
UPDATE 13 Sept 2022 SPLIT Wings and Rear Fuselage Allows all bits to fit on 220x220x200 printer Note: Wing1 should to be diagonal to fit on bed VERSION 3 - MAY 2021 Update Full Airfoil / thicker wing / close to ClarkY 2 piece Canopy for easier...
thingiverse
VERSION 4 - MAY 2021 Update - Full Airfoil / thicker wing / similar to ClarkY - 2-piece Canopy for easier printing - Improved profile Ailerons - Removable landing gear anti-rotate tabs - RECOMMEND - Half Travel on Elevator All STLs refreshed...
thingiverse
Specifications: Airfoil: ClarkY modified Wing span: 1550 mm Wing chord: 285 mm Aerodynamic center: Overall weight: 3500 g Wing weight complete: Fuselage weight complete: Wing area: 44.18 dm² Wing loading: 75 g/dm² Motor: NTM 35-48, 900KV, 815Watt...
thingiverse
For the picture I've taken a ClarkY and an Eppler 625 airfoil. Please follow these easy steps to get the STL files you want: 1. install openSCAD: https://www.openscad.org (it is free of charge) 2. open the propeller.scad file of this thing (a...
thingiverse
The airfoil I'm using is a "Clark Y" (http://airfoiltools.com/airfoil/details?airfoil=clarky-il). It's tough to keep the STL files up-to-date on Thingiverse because I do lots of small changes. If someone is already interested in the parts, just...
thingiverse
On AirfoilTools, select clarkyh-il ClarkY from the drop-down list and adjust the chord length to 200mm + 35 for the aileron. After obtaining the airfoil template, clean it up in Inkscape or directly within 123D Design. Mark out the aileron, spar...