clamps for makita track saw 3d models

My contactor was using a track saw and I saw he had a duct-taped pipe fitting connecting his Makita track-saw to a Makita portable vacuum, and it kept popping off mid-cut. I slapped this together in Tinkercad and printed him one as a better...

This is an adapter to connect the Makita track saw to a 1-1/4 standard vacuum hose (shop vac or similar). I used "low quality" resolution since it's just a functional part. ... Took about two hours to print.

... and a Powertec guide rails. ...When I put it on my XSH04 Circ Saw, I had to give it a little gap to not cut away too much of the rubber. ...I designed this little spacer to slip on so that its the exact same space every time I put this on my saw.

Simple holder for the tracks of the Makita track saw. Use 4,5 x 35mm wood screws for the `bottom` part. Use 4,5 x 20mm wood screws for the `top` part. ... Each part required 2 times.

https://youtu.be/XmLjWxxfME0 I designed a wall and ceiling mount for the Makita saw guide rail. ... Use metric screws M5x20 to button mount and 3.5 - 4 mm screws of the required length to fix the bracket to the wall or ceiling.

These are the bushings to keep the slop out of a Makita track saw. ...When the print is done cut aa small slice through the ring vertically to let the ring expand when the screw is turned.

I've got a Festool/Makita deflector that you can print and assemble using M5 countersunk screws with their M5 nuts. For more details, check out my blog at https://makeverse.home.blog. I just published an article related to this project on my blog,...

I made this adapter specifically for Powerfix/Parkside one hand clamps (medium and big size). I needed them to fix the track of the Parkside track saw. Makita clamps cost around 20€, so...I designed my own! Works well, but you just need to put a...

This end piece clips very easily on Makita saw tracks. The bumpers can be clipped on one another for storage.Print instructions:PLA 0.3 mm layer height. Faced down.No supports. Update 20240227:Added a no logo version (v13) There's a Festool saw track...

This end piece clips very easily on Makita saw tracks. The bumpers can be clipped on one another for storage.Print instructions:PLA 0.3 mm layer height. Faced down.No supports. Update 20240227:Added a no logo version (v13) There's a Festool saw track...

This is a slide adapter to use your Makita Track Saw track with a Makita 196094-2 Compact Router Plunge Base. Requires two 1/4-20 nuts and short pieces of 1/4-20 allthread (or long bolts with the heads cut off). Drop the nuts in the slots and...

Super Simple Guide for a DIY Track Saw Tracksaw is just a piece of Ply or MDF with a 12mm Alu Angle attached, This print keeps the Saw from drifting away from Alu angle. ... Slots into the Existing Guide slot on a Makita Saw and is secured by the stock...

This adapter fits the outer diameter of the Makita XPS01PTJ track saw. The inner diameter from the vacuum hose is for a 1 1/4 inch connector. This fits perfectly on my setup with just the right amount of grip. Your mileage may. Purple,...

This is a dust cover for the Makita SP6000 corded track saw. It is not my design. Someone saw a picture of it on one of my designs and asked me if I happened to have the file and could re-upload it because Thingiverse seems to have deleted it. I...

A budget-friendly option for DeWalt track saw clamps. The design draws inspiration from the Irwin micro quick-grip. https://www.amazon.com/IRWINQUICK-GRIPOne-Handed-Micro-Clamp-Pack-1964747/dp/B00004SBCO I printed these with 5 walls and 100% infill...

This cover/cap is for the Makita 18V X2 (36V) LXT Brushless 6-1/2” Plunge Circular Saw, model XPS01. The cover is very precise. ...It will keep dust from escaping through the side opening, thus improving dust collection.

This cover/cap is for the Makita 18V X2 (36V) LXT Brushless 6-1/2” Plunge Circular Saw, model XPS01. The cover is very precise. ...It will keep dust from escaping through the side opening, thus improving dust collection.

This adapter fits the outer diameter of the Makita XPS01PTJ track saw. The inner diameter from the vacuum hose is for a 1 1/4 inch connector. This fits perfectly on my setup with just the right amount of grip. Your mileage may. ...Purple,...

Repeatable rips with the Makita track sawThis fence makes it easy to cut precise strips of exactly the same width when panel cutting. Two side fences are mounted on the guide rail for this purpose, and the required dimension is set via the...

A simple connector that slides in the makita tracksaw rail T track, and allows connecting a DIY version of parallel guides. ...

This cover/cap is for the Makita 18V X2 (36V) LXT Brushless 6-1/2” Plunge Circular Saw, model XPS01.The cover is very precise. ...It will keep dust from escaping through the side opening, thus improving dust collection.Be sure to check out slipangle28's...

Here's a replacement head for the Irwin Micro clamp that lets you use it on track/plunge saw rails. Just remove the original clamp head and swap it out for this one. Since these clamps are super affordable, I'd suggest securing them with pins and...

I was frustrated that the vacuum molded insert for my Makita cordless tracksaw systainer was falling apart. In addition it resulted in a lot of empty space in the box. This is a work-in-progress that I modeled very quickly to serve a purpose so its...

Update: An additional file is added for anyone with tracks that are fitting tight. This new file has an extra 2mm of spacing added. Also it has come to my attention that if the print is printed on it side it can be easier for some with the cam to be...

You will need some M6 nuts and bolts and 2 rulers Blue Spot 33934 24-inch Aluminium Ruler https://www.amazon.co.uk/gp/product/B002HMQE86/ref=ppx_yo_dt_b_asin_title_o02_s00?ie=UTF8&psc=1 The rulers will need to be cut to show the correct dimension...

Print one base and one nut in the default STL orientations (flat for the nut and on the side for the base). This will give the best strength and will require no supports.</p><p>Assemble base to nut with one M6 x 20mm hex bolt and nut. You can play...

Print one base and one nut in the default STL orientations (flat for the nut and on the side for the base). This will give the best strength and will require no supports. Assemble base to nut with one M6 x 20mm hex bolt and nut. You can play with...

Yet another track saw clamp. There are a bunch of these on here already, but I could not make any of the ones I tried work. Some were too loose, and the clap bar would deflect and there would be no clamping force. Others would not close all the way...

... lift the saw. I designed a hose guide that simply clips onto the track and a saw-to-hose outlet adapter that has a smaller angle than the original. There is no need to hold the hose by hand. ... To assemble, use M5x20 hex head bolt and M5 nut.

Track saw attachment that will fit a Milwaukee saw and a festool track. You need 1 length of Aluminum or Steel to fit in the cavity that will connect to your saw. The other models on here all have 3d printed arms which isnt strong enough to last...