clamp 3d model

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_wall_thickness = 1.6 custom_back_camera_corner_resolution = 8 custom_left_port_corner_resolution = 8 custom_corner_resolution = 8...

For any other question, please feel free to reach out, or leave a comment. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: Yes Resolution: .2mm Infill: 20% Filament: Jarees PETG Matte Black Notes: Support is only...

Required hardwareRaspberry Pi Pico (RP2040) microcontroller boardUSB cable (as it has to be cut and soldered a USB 2.0 is preferred, because it only has 4 wires)4x Cherry MX key switches or other with similar size4x Keycaps (or print your own)4x M2x6...

  I've been using the one in the picture for a few weeks and apart from not looking as pretty with the cam open, there's absolutely no difference in performance.I think I have allowed enough room to print this model with a .6mm nozzle but if you are...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_position = 0 custom_right_port_y_position = 0 custom_phone_thickness = 10 stencil_pattern_element_rotation = 0...

See Latest Updates Below ----------------------------------- * The latest model now appears at the top due to rearranged pictures. I wanted a unique look for my 4x Santa figure, if that's feasible... Took various elements from multiple 4x...

I hope this piece works for you; it was actually the most challenging to model and get right. 9. You should be good to reassemble now! 10. Put the hammer-trigger-piston assembly back in. 11. Lay the cylinder back in place, including the U-clip for...

Don't use it for rendering or model generation. (see Reducer picture)</p> <p>PRINTING NOTE</p> <p>Print at 100% infill. Try and print standing vertically, if possible so that scaffolding may be ommitted on the inside.</p> <p>These are for sink and...

All necessary supports are pre-applied to the models (there is no need to add additional supports). The main body of the stein/mug prints with cylindrical supports, the left/right lid have perforated supports, the lid top doesn't require supports...

If you want to save time while testing, you can print the included **calibration test** instead of the full model, but that is optional. Once the egg halves are printed, screw the threads in and out repeatedly to remove any stray particles. It...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_x_position = 20 custom_back_camera_corner_resolution = 8 custom_bottom_fillet_resolution = 8 stencil_horizontal_position = 50...

I have no model or figure of Buffaloman in a camo tank top. The bazooka is actually pointing backwards to simply be held resting on his shoulder. I scaled it to 40% and positioned it to be resting between two shoulder spikes with the hand grip...

Eye diameter - These three dimensions make up the foundation of this model's unique structure, resulting in eyes that stand out at an impressive six units large. Layer height - Perfect for intricate designs or subtle layering, with a precise setting...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 use_stencil = 1 stencil_shape = 7 stencil_size = 40 stencil_mirror = 0 custom_back_extra_port_x_size = 30...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

So far my failures are in optimizing the printer tuning to keep the model airtight. As stated in the Harvard paper, they printed a form and molded silicone for the soft actuators. I probably should do that too, but I am determined to work with FDM...

I've updated the model with the Orbiter Ver. 1.5 as I purchased another one (I don't want to take the one I'm using on my Bear off as it works soooo good). I've also updated the filament sensor to use the Prusa MK3+ sensor as I have two of them. I've...

I've designed some custom shelves for my Warhammer 40K model painting supplies, including paints from various manufacturers. The system allows you to mount two shelves on either side of a wall and connect them with chains. For instance, you can...

The COMPLETE Dragonpeak Barbarians I bundle contains every model of this set, from the modular units to the heroes, the mount, the Pinup and the terrain piece! The people of Dragonpeaks are direct descendants of the Humans who lived in Aera under...

--------------------------------------------------------------------------------- Print Settings: • Ensure the model is orientated as shown in the slicer image • Skirt - Yes • Skirt Line Count - 2 • Skirt Distance - 1 mm • Support - Yes • Support...

It started with a Bachmann starter set with a steam loco and a couple of cars (Durango & Silverton in case my other models didn't give it away). This came with a bunch of EZ-track. I had full intention of expanding my layout so I bought more...

One suggestion offered is to quickly wave fire under the problem area in the hopes that the hair will burn away before the plastic is damage, but I came up with a different solution.This set of models replaces the entire front wheel assembly. The...

A .3mf file is available along with the STL models.Assembly/MountingThe inner fixture can be held upside-down to desired mounting position for marking the mounting holes. I found it works best to drill a first hole and then insert a screw into that...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_position = 0 custom_right_port_y_position = 0 custom_phone_thickness = 10 stencil_pattern_element_rotation = 0...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 11 custom_back_extra_port_corner_resolution = 8 custom_bottom_fillet_radius = 1.6 custom_left_port_corner_resolution = 8...

Find it according to your vacuum cleaner model. In the file, you can also adjust all necessary parameters, including the angle for the vacuum cleaner adapter. Copy these values into the snipper file as well, since the first section's angle is needed...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_width = 100 use_mouse_ears = 0 pattern_element_overlap = 52 stencil_shape = 3 custom_back_camera_y_size = 20...

Tools Hex wrench 2mm and Mmm...

They were sold to me as "boat nails", feel free to substitute them for something else and adjust the model accordingly. For the spark gap I used a couple of bits of single stranded wire, these can be substituted for something else, multi-strand...

The bowl model is a solid piece, and CAN be printed in vase mode / spiralize outer contour. This, however, isn’t the strongest. What I do is print them with 0% infill, 2-3 outer walls, 4 bottom layers, and 0 top layers. Basically makes it a double...