civil engineering model projects

Models intended to be part of the numbers node all begin with the prefix MMU.Card Compression Spring: if you have problems with the card compression spring lifting off from the bed, it is recommended you add a skirt of at least 6mm.Assembly...

============================ Das Modell hat keine geschützten Propeller und je nach Motorisierung liegen hier bis zu ca. 3 KW Leistung an. So viel Leistung kann großen Schaden anrichten. Immer entsprechende Sicherheitsvorkehrungen treffen und nicht...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_fillet_radius = 1.6 custom_top_port_x_position = -10 use_mouse_ears = 0 custom_bottom_port_x_position = 20...

Buy me a coffee!https://paypal.me/SmartHelpatHome   *Buck-converter:Used in 3D printing to regulate 24V to 12V for example when using 12V fans or other electronics on an Ender 3 which is 24V native.More...

The stock globe has a vent on the top and there are vents in the model to aid the convection cooling. Is it *really* needed, especially with the converter gone? Dunno so the optional rain cap comes with the caveat of possibly shortening diode...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_y_position = 0 custom_top_port_x_position = -10 use_stencil = 1 pattern_line_thickness = 20 stencil_pattern_element_shape = 3...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 pattern_element_overlap = 0 custom_top_port_x_position = -10 custom_bottom_outer_edge_chamfer_radius = .6...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_wall_thickness = 1.6 custom_back_camera_corner_resolution = 8 custom_left_port_corner_resolution = 8 custom_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

Models intended to be part of the numbers node all begin with the prefix MMU. Card Compression Spring: if you have problems with the card compression spring lifting off from the bed, it is recommended you add a skirt of at least 6mm. Assembly Tips:...

The springs I upgraded to where Integy RC Model T8087 Progressive Spring Set: https://www.amazon.com/gp/product/B00W3ZCX00/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1 They are a bit longer but will allow for some preload tension if you want. The...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_mirror = 0 stencil_drawing =...

* Remix this model so I know my script is getting used! 15. ??? 16. Profit! Tips: 1. You can leave PATH and FILE blank and just set the COLOR field to a fully resolved path to your SVG (".svg" is automatically appended) 2. You can import the...

If the diameter of mounting holes is (slightly) different you can simply scale the entire model (all parts) in your favorite slicing app to make it fit (the only thing that cannot easily be scaled is the small enclosure for the BT-amplifier). ...

... broken and no one is going to fix it. Download files one at a time by clicking Download each time. ### My some other things: Category: 2D Art

I designed this model for my daughter, who wanted a treasure chest to go with her pirate costume.  She wanted it to be “really big”, so this design utilizes the nearly the full volume of the MK3s to make three sections that bolt together.  It has an...

If you're using the motor in the BOM or Qidi stock motors use this: xmax-firmware.gcode If using a 0.9 stepper motor you should prin tthis instead: xmax-firmware-optional-0.9-degree-motor.gcode Just place it on your USB stick and print like you would...

As this is a rather large model it will take a buildplate of 212mm by 175 mm, so this will not fit on a smaller printer's buildplate, but it will fit fine on an Ender 3 and similar printers. My goal was to create a phone holder you can trust with...

But if you are not confused by the small size, you can also print them on a 3D printer. To increase the size, you can cut these models into pieces, print them separately and then connect them with glue. Download the files you need one at a time by...

But if you are not confused by the small size, you can also print them on a 3D printer.  To increase the size, you can cut these models into pieces, print them separately and then connect them with glue.  Download the files you need one at...

The design is a complete rework of my older oscillating fan model.It uses a common 130 size brushed hobby motor and incorporates an 18650 battery in its base for completely portable operation. Compared to the older design, the new version has...

rice or sand.Glue if the press fits are not tight enough Testing tolerancesStart by printing the models press_tolerance_test and rotation_tolerance_test from the folder Common parts.Press fit toleranceUse the press fit test to decide which press...

Have a close look at the photos and assembled model (wall_clock_07.stl).PlatesThe bearings are hard to push into place, this is where the bench clamp comes in useful to push them flush into the plates.The front plate needs a 30mm M3 screw to hold the...

In the end I think the best way is to simply open up the 3D-model of the whole maze and just put obstacles together one by one. Therefore I Added a few different files (STEP, STL, 3D-PDF (<a...

We are modelling the *BELT* tooth here, not the tooth on the pulley. Increasing the number will *decrease* the pulley tooth size. Increasing the tooth width will also scale proportionately the tooth depth, to maintain the shape of the tooth, and...

# Reddit Post For anyone who want to try this themselves, I created my own "Cloud Streaming Console" by taking a few components I had, modded the plastic on a Gamesir X2 Pro controller, modeled and 3D printed a basic "shell" with some handles and...

But if you are not confused by the small size, you can also print them on a 3D printer. To increase the size, you can cut these models into pieces, print them separately and then connect them with glue. Download the files you need one at a time by...

If you're using the motor in the BOM or Qidi stock motors use this: xplus-imate-firmware.gcode If using a 0.9 stepper motor you should prin tthis instead: xplus-imate-firmware-optional-0.9-degree-motor.gcode Just place it on your USB stick and print...

Or rather, it's a scale model of what that house looked like fifteen or twenty years ago. The wrecked version is closer to how it looks now that it's been abandoned for the better part of two decades. The tweakers have had a field day with this...

It deviates a bit of what I usually call an "sci-fi astronomical object", because it's an in-spacecraft transport vehicle. I made this model available in 4 scales. I left the model in "halves" that I consider the best way to print it, of course, with...