circuit breaker model

... one at a time by clicking Download each time. Or click Download once on the file Girl_Unicorn.rar ### My some other things: Category: 2D Art

If you want to use the hardware I intended this to use:Hinges Bolts- https://www.mcmaster.com/91292A018/ (you will need to thread inner most hinge)Hinge spacer- https://www.mcmaster.com/91755A311/ (you can see in the photos a little bit of white in...

... one at a time by clicking Download each time. Or click Download once on the file spider__man.rar ### My some other things: Category: 2D Art

The design uses 12 '10mm x 3mm' (the magnets are actually closer to 9.95mm x 2.67mm).This is a spin-off from my earlier light-pull magnetic door catch: https://www.printables.com/model/209370-magnetic-low-profile-floating-head-quiet-door-catc , but...

Dimensions: 510 m × 330 m × 241 m Model scale: 1:3x103 (15cm) 1:8x103 (7cm) References "Lawrence, K. and Benner, L., Radar shape models of asteroids compiled by Lawrence V1.0. urn:nasa:pds:gbo.ast.jpl.radar.shape_models::1.0. ...NASA Planetary Data...

A wrench is used to unscrew the end caps for relamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap. 7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.Superior...

A wrench is used to unscrew the end caps for re-lamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap.7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.Superior...

The Raspberry Pi controller has a radio module attached to it for issuing commands, though I used the slightly different NRF24L01+PA+LNA model which offers better range. You could also use the same NRF24L01+ module as the puck uses, the wiring and...

Please review the filenames, model file comments, and pictures before starting.Non-printable parts and necessary tools:The clock movement and clock second...

  I also modelled in clips for these PCBs to hold them in place whilst soldering up.I will share my order for my PCBs on jlcpcb so anyone can order once I figure out how :D Tools RequiredSharp knifeLong Nose Pliers Note that the 3mf...

I would also suggest allow for extra LEDs in your strips and to slide in your LED strips as you combine a segment to other segments. All in all, I learned a great deal about modeling using Fusion 360 and 3D printing using Slic3r and the Original...

If in doubt refer to Mehdi for more demonstration material.I was basically trying to address two "issues" of my Anycubic Vyper:The PSU and Mainboard 24V fans are very loudI want to upgrade my Vyper with an OctoPrint/OctoPi setupSo here is my...

 A lot of my models are designed for the 2.49mm walls that equate to 6 print lines with a 0.4mm nozzle.  </p><p>Both the Tool Holders and the main Jig are setup to have a color transition at Z height. ... </p><h3>Donations</h3><p>If you found this print...

Depending on your printer tolerances, it may be more or less tight, but if everything lines up it should be no problem.Fasten the 3 screws at the "top" (in this orientation) once the spine is flush with the caseCHANGELOG2022-03-01 - Moved away from...

This version is included for those that want to create a custom playing field using other materials.Other Printing NotesWhile I was able to get pretty good results printing the sidewalls without supports, I did get better results adding a couple of...

Depending on the figurine put on top of the box a different playlist ist played, currently mostly kids audio books and a spotify music playlist.All in all a very cool project that i hope to expand when my son grows older.ElectronicsPhonieboxRaspberry...

&nbsp;Foam card (if you're not already familiar with it) is a material used in the art world and in crafting or modelling situations, a layer of foam is sandwiched between 2 layers of card, the resulting material is incredibly strong and is generally...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_fillet_radius = 1.6 custom_top_port_x_position = -10 use_mouse_ears = 0 custom_bottom_port_x_position = 20...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_mirror = 0 stencil_drawing =...

I am planning to use 4mm pneumatic connectors to attach a teflon tube but you are free to use some filament guide from any of the listed projects from where I remixed.What you need to buy:1x Ikea Samla 22l including cover2x 8mm thread-rod, 338mm (can...

But if you are not confused by the small size, you can also print them on a 3D printer. To increase the size, you can cut these models into pieces, print them separately and then connect them with glue. Download the files you need one at a time by...

As this is a rather large model it will take a buildplate of 212mm by 175 mm, so this will not fit on a smaller printer's buildplate, but it will fit fine on an Ender 3 and similar printers. My goal was to create a phone holder you can trust with...

We are modelling the *BELT* tooth here, not the tooth on the pulley. Increasing the number will *decrease* the pulley tooth size. Increasing the tooth width will also scale proportionately the tooth depth, to maintain the shape of the tooth, and...

If you're using the motor in the BOM or Qidi stock motors use this: xmax-firmware.gcode If using a 0.9 stepper motor you should prin tthis instead: xmax-firmware-optional-0.9-degree-motor.gcode Just place it on your USB stick and print like you would...

WARNING: To make sure you're looking at the latest version of our files and documentation, we strongly recommend that you navigate to the Official Project Page. V-Core 3 The V-Core 3 is a premium DIY kit for a CoreXY 3D Printer with no compromises....

The ability to visualize 3D models in real-time enables users to make informed decisions about color palettes, proportions, and overall aesthetic. This level of precision is unmatched by traditional design methods, making Shining 3D Fashion a...

If you're using the motor in the BOM or Qidi stock motors use this: xplus-imate-firmware.gcode If using a 0.9 stepper motor you should prin tthis instead: xplus-imate-firmware-optional-0.9-degree-motor.gcode Just place it on your USB stick and print...

From there I just drew out the parts and extrudede them in the modeling tools, then exported them to STL files and printed them out. Project: Laserscythe - Another Open Source laser engraver using recycled doohickeys Project Name: Project:...

Learn everything about the V-Core 3 on the dedicated project page: v-core.ratrig.com. External links: Buy Kit at Rat Rig Step by step Build Manual Facebook Rat Rig 3D Printer Community Project Page (BOM, Build Guide, Files, Electronics, Firmware)...

Have a close look at the photos and assembled model (wall_clock_07.stl).PlatesThe bearings are hard to push into place, this is where the bench clamp comes in useful to push them flush into the plates.The front plate needs a 30mm M3 screw to hold the...