cidora sl5 e 3d models

For using the standard gopro flat mount on your drone, if you don't want to mess around with TPU mounts Note - this has been made thicker than the original, because it broke with thinner arms while I was flying that version. I printed this at 80%...

cidora sl5(227mm) ray

227mm iflight cidora sl5 frame

IFLIGHT CIDORA SL5 V2.1 BACK BUMPER

GPS Mount for frame iFlight Cidora SL5

IFLIGHT CIDORA SL5 V2.1 BACK BUMPER Print instructionsUnassociated tags: 2.1 Category: 3D Printing Summary IFLIGHT CIDORA SL5 V2.1 BACK BUMPER

Set of parts I created to replace the original TPU parts for the 5" Iflight Cidora SL5 V2.1. ...

FPV Camera Mount for the iFLight Cidora SL5. Made for Runcam Micro Sparrow and Runcam Micro Swift. But any Camera with a width of 19-20mm may fit. ...

Set of parts I created to replace the original TPU parts for the 5" iFlight Cidora SL5 V2.1.To print the right hand arm guard, just mirror the left hand one in the slicer.

Hi. ...I designed a 25 deg camera mount for attaching caddx orca to the iflight cidora sl5 or xl5. The base is 4mm. screw hole is m3. ...there are holes for easy screwing

Set of parts I created to replace the original TPU parts for the 5" iFlight Cidora SL5 V2.1.To print the right hand arm guard, just mirror the left hand one in the slicer.

Designed a rear guard for my iflight cidora SL5. I whanted to protect the caddx vista from most of the potential dirt and debris. While adding som holes for increaced cooling purposes. I have added two diffrent versions: 1: This version have holes...

Antenna This one fits the iFlight Cidora SL5 frame (I believe the Nazgul is using the same frame, so it should fit). Print the Air Unit holders the outside wall flat (requires no supports). I printed mine using PETG, PLA would probably work too,...

Mounts to hold a micro fpv camera in the front of the SL5 frame. Print two times (one for each side). ...Use a M2 screw to secure the cam.

iFlight Nazgul XL5 V5/ Cidora SL5 V2.1 Arm Guard

Original design by Acal51 for Nazgul XL5. ... This is a remix to fit Cidora SL5 V2.1

Remix of thing: https://www.thingiverse.com/thing:4190551 Adapted for iFlight Cidora V2.1 SL5 Freestyle Frame. ... Measurements for mounting with screws: 25x36mm

This was my first challenging multirotor design, and printing experience, as it needed to securely hold a bn-220 gps unit. The mount's potential versatility could make it suitable for any quadcopter featuring 25mm between screw holes. However, I'm...

After the first flight, I ditched the foam feet that came with the kit - yay, learning to fly! Next, I decided to design some new feet to make flying better. To get started, you'll want to pick up some screws that are a couple of 4mm longer than what...

Il mio modestissimo supporto universale per action cam. Si stampa in TPU. ...Si utilizza con tutti i supporti originali delle actioncam.

This is a simple expresslrs ep1 rx antenna mount for cidora SL5 V2.1 frame. And its a remix from https://www.thingiverse.com/thing:5341070 , as the original was not for cidora. ...So i combined the mount with cidora back bumper.

This is a simple expresslrs ep1 rx antenna mount for cidora SL5 V2.1 frame. And its a remix from https://www.thingiverse.com/thing:5341070 , as the original was not for cidora. So i combined the mount with cidora back bumper. ... Category: 3D Printing

Vertical Mount for Insta360 One R Designed to be mounted to the iFlight Cidora SL5 v2 FPV Quadcopter frame. to create perfect Tik Tok Freestyle drone videos. https://www.tiktok.com/@jimbigo I use 25 degrees of camera up-tilt and mainly use the 4k...

I designed this Mount in Tinkercad for my quad, it fits perfectly on the iFlight Cidora SL5 5 Inch frame but might work with otheres as well. The dimensions of the holes are 36mm x 25mm and Its tilted at 30 degrees. Mounting this to the drone is...

1.5mm shims for the cidora fpv camera. ...installed between the carbon plate and the fpv camera

I made a quick and primitive GoPro11 mount for my FPV drone, since I couldn't find any online. It's slightly tight but works just fine. ...I forgot the hole for the front display, so I had to cut that out by hand, but the 3D model could easily be...

This bracket is engineered to securely attach the Beitian BN-220T GPS module to the top-front of the iFlight Cidora SL5 and Titan XL5 frames, utilizing existing M3 screws that offer ample length for a rock-solid hold while also providing sufficient...

This bracket is designed to secure the Beitian BN-880 GPS module on top of the iFlight Cidora SL5 and Titan XL5 frames' front side.\r\n\r\nThe existing M3 screws are long enough to hold the bracket firmly in place while still providing a strong grip...

A combined mount for the Axii VTX antenna, Crossfire Immortal-T, and a BN-880 GPS for the iFlight Cidora SL5. I couldn't find anything existing. The BN-880 is meant to be press-fit and catch on the sides. It worked, but still worried me just a...