chromecast remote case 3d models

If you have problems getting the pieces to fit together, you can adjust your slicer settings, or in an extreme case, modify the `dual-reel.scad` file. Increasing the `radialEase` variable should make the objects fit more easily, and decreasing it...

I already had pre-spliced wires so just soldered them on with some excess just in case. Check the video by SonnyWheels mentioned earlier in the notes to see how to wire into this connector if you're unsure. I would recommend taking your time and not...

In this case, I recommend satisfying the M3x8 DIN7380 (BHCS) screw with screws M3x8 ultra low profile ________________________ Purchase list necessary for the correct assembly of the mod: [1x] Sherpa Mini Extruder (BOM below), or: trianglelab - ...

## Parts required: - 1x 5 gallon bucket - 1x 3.5 gallon bucket (you might be able to use another 5G bucket here, but the smaller one is generally cheaper and is less wasteful) - 2x 12" (standard size) bucket lids - 12x 1/4"-20 x 1/2" machine screws...

Supports touching the build plate (only) are suggested, in any case no supports are needed on the threads. 0.1mm resolution Post-Printing Putting it together First, make sure to clean the "elephant foot" from the parts and also clear any supports. I...

In this case, please contact, it is possible to save files at high values, but this will give a sharp increase in file size. This is a fully solid-state version for 3d-print, this is not a scan version. At the photos you can see the contours of the...

The final check is to hold the probe or bolt stationary with one hand and rotate the SPA with the other to verify you're able to easily rotate the SPA, thereby adjusting the height of the probe (or in this case, the bolt). Installation:Loosen the...

If one side is up the other side is down), and the nut traps in the leg_drive_disk will be on the side toward the frame.  Turn the main drive gear to make sure that everything rotates without binding.  Then tighten the M4 clamp nuts on the...

The parameters with which the pieces were printed in my case were: low quality profile with layer height of 0.28mm, 10% cubic infill and support for the pieces and adhesion Raft was used (see picture above for more details).The material used for...

I prefer screws in this case because the plate is exposed to significant loads. In addition, precise bonding is not always easy.</p><ul><li><strong>2 x M5 screw</strong> (not required when using superglue) Hexagon socket, thread length min. 20mm,...

The difference between the sizes, is the length of the modules (in case the rack being used is not very deep): Regular 147mm Short 108mm Extra (ex-) Short 91mm There is also a version of the Extra Short center box which does not have a vent for the...

If you still have problems, then please visit the original thingieverse publication (https://www.thingiverse.com/thing:4267901) where I have added some custom parts for such rare cases. Please adjust temperatures and material parameters for your...

For the whole system you need additionally: Car battery which is minimum 300cca (There has been said minimum 200 is enough but just in case ;)) You should keep the battery full as far as possible. Timer module:...

In this case, please contact, it is possible to save files at high values, but this will give a sharp increase in file size. This is a fully solid-state version for 3d-print, this is not a scan version. At the photos you can see the contours of the...

In this case, please contact, it is possible to save files at high values, but this will give a sharp increase in file size. This is a fully solid-state version for 3d-print, this is not a scan version. At the photos you can see the contours of the...

In my case, there is an overheat issue with the extrusion stepper (it's hotter than other stock steppers), I think the new stepper has lower voltage than the stock one, I will add a buck converter to fix that. But it's not a design issue anyways. It...

Of course, infill type and amount are not critical if printing the “gearwheel” type tire.Do not forget to use a glue stick or painter's tape as an underlay when printing TPU on a PEI base - otherwise it will stick “a little” too good to the...

In this case, please contact, it is possible to save files at high values, but this will give a sharp increase in file size. This is a fully solid-state version for 3d-print, this is not a scan version. At the photos you can see the contours of the...

It will take you no longer than 65h and no more than 309g or 39m of filament to have it 3D printedAs in the case of all our 3D models, Terran files are available for download in STL format and perfectly print out on an average priced SLA/SLS or FFF...

If you are using a 16 LED or 24 LED NeoPixel Ring, simply change the LED_COUNT to 16 or 24 accordingly. Each NeoPixel LED can draw up to 60 milliamps (worst case) and the Arduino Nano can comfortably power 6 NeoPixel LEDs. Adjusting the LED_COUNT...

In this case, please contact, it is possible to save files at high values, but this will give a sharp increase in file size. This is a fully solid-state version for 3d-print, this is not a scan version. At the photos you can see the contours of the...

In my case I only have the rear bars to trigger against. If you've got an enclosure or frame, it might be preferable to mount it with the trigger on the front.Additional Hardware Required:0.5mmx3mmx10mm 304 Stainless Steel Compression Springs...

In my case, there is an overheat issue with the extrusion stepper (it's hotter than other stock steppers), I think the new stepper has lower voltage than the stock one, I will add a buck converter to fix that. But it's not a design issue anyways. It...

In case you lose track of how many printers you have or just want to dress them up a little bit.Supports are painted on the inside and easily removed.Quick and easy printDesigned on...

 Part 4 and 5 are ment to hold with carriage bolts to the backrest, these should point with the head to the rear, accordingly the...

http://www.thingiverse.com/apps/customizer/run?thing_id=46884 Using the following options: qr_rotate = 0 qr_bottom = 1 qr_thickness = 5 perimeter = -1000 code_flip = 1 tag_thickness = 3 qr_scale = 1.6 case_thickness = 2.4 tag_width = 80 tag_height =...

In that case, use M2 hardware and print the parts that end with “M2”. Only the Skadis T-Nut &nbsp;and the Mounting Plates are different depending on the screws you use. The Arms and Flappers use M3 hardware.</p><p>&nbsp;</p><h3>Printed...

In this case, please contact, it is possible to save files at high values, but this will give a sharp increase in file size. This is a fully solid-state version for 3d-print, this is not a scan version. At the photos you can see the contours of the...

In this case, please contact, it is possible to save files at high values, but this will give a sharp increase in file size. This is a fully solid-state version for 3d-print, this is not a scan version. At the photos you can see the contours of the...

Ideally, you have to have CR-Touch (my case) or BLTouch installed. Remove the extruder assembly, cut the wires in the center and extend them by about 120mm. Print and install the extruder repositioning bracket along with the extruder assembly in...