chris roberts model

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_y_position = 0 custom_top_port_x_position = -10 use_stencil = 1 pattern_line_thickness = 30 stencil_pattern_element_shape = 3...

... class="media"><oembed url="https://vimeo.com/758042056"></oembed></figure><p>Gear ratio =2&nbsp;</p><p>STL are given on the recommended printing orientation, <strong>no supports needed</strong>. all models fit a prusa mini.&nbsp;

I will upload my attempts, but I advise only using them for modeling purposes only, or if you can get them machined out of aluminum or something. Only then will they be strong enough. If your stem is too low or your cable housing is too short, then...

You can fit dividers in any space, and they fit next to each other too if necessary, but you probably don't want to fit one in the front space as it will block the finger hole in the front of the drawer.If you make one of these, please post your...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_y_position = 0 custom_top_port_corner_radius = 5 custom_left_port_length = 50 pattern_element_rotation = 27...

Note: these videos are uploading slowly, so they might not be fully processed when I publish this model. They should be available in a few minutes.</p><figure class="media"><oembed...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_width = 100 use_mouse_ears = 1 pattern_element_overlap = 0 stencil_shape = 7 custom_back_camera_y_size = 20...

Concept: This is a scale model of a possible two to four person habitat to be shipped to mars. The idea is to have a majority of the craft built on earth, with only a few modifications and additions needed once on Mars. This kind of structure will be...

Note that the Shapeways model has been modified to meet their minimum wall thickness requirement, so looks a little different; it uses the same idea. You'll need to order two if you get it from Shapeways, since it's only half the puzzle. On the plus...

For more details, visit http://www.thingiverse.com/thing:47032 [^] (v.1) naio naio naio naio naio naio naio naio naio naio naio naio naio naio naio naio naio naio naio naio naio naio naio naio naio naio naio naio naio naio naio naio naio...

Creality slicer use edit, multiply selected models. PrusaSlicer use cut and past. I'm sure it's possible in other slicing software too. I would recommend printing a few extra as you may damage the edge on a few when inserting them. Assembly: ...

Furthermore I created the endstop mounts which are already present in the Fusion 360 model. I will try to update the pictures today or tomorrow. Now it gets exiting! Electronics are next! **Update 9** (03.07.2018): After test driving the Z-Axis I...

It should be possible to customise the model by changing a global variables that represent the battery dimension and straps width- holes for the LED indicators- reducing the number of screws- creating the cases for wider range of IMUsPlease let me...

A .3mf file is available along with the STL models.Assembly/MountingThe inner fixture can be held upside-down to desired mounting position for marking the mounting holes. I found it works best to drill a first hole and then insert a screw into that...

It was just hard to get some of the screws in it so I had to manually remove the parts this model has removed for you. Make sure is you use screws to hold the bearings tight that the lowest ones have low profile heads or they will be lower than the...

About this model: Things are a bit wonky aligning the pieces. As mentioned this wasn't done in CAD software... But they will line up. Once you get things put together you may wish to super glue some of the pieces to provide stabiltiy and less...

You could group them in Tinker and make a single/twin mega model - love that Tinker feature! Support is required in places due to geometry, but it's very simple square profile support that is easily removed. I always try to avoid it, but not at the...

... that is about 1/4"/5mm in the front center due to the belt tensioning clip bumping into the blower. Unless you like that kind of centrifugal blower fan on belt tensioning clip action, I recommend not to drag the models dead center to the front.

This is a modification to the SlideSnap Pro: https://slidesnappro.com/ At the time I bought a SlideSnap Pro, they had two models, the SlideSnap Pro, and the SlideSnap Lite. Both are based on a refurbished and modified Kodak carousel projector. The...

This set may fit other models. I can't make guarantees on fitment.\nAnyone familiar with the Makerbot series printers will know that it's quite dark in the build space. They provide you with a roving white LED, and a red AMBIANCE LED which is both...

Currently, there are three models:Ebook Reader Holder (1x3):This was designed for my Kindle Oasis in its third-party case (if you want it for something thicker than ~15mm, let me know and I'll see about whipping you up a variation)1x3 footprint on...

I also designed roller bearing(it was harder than I though) which works great (better than anything I found on thingy) but a also included modified gear bearing from emmett (https://www.thingiverse.com/thing:53451) which could potentialy be...

I made a slight modification to the model by changing the profile of the USB input so the bridge was less than 5mm (was almost 10mm) and changed the way the board mounts so the top has all socket heads and no washers (just an aesthetic thing). <a...

Print Settings Printer Brand: Ultimaker Printer: Ultimaker 2 Rafts: No Supports: Yes Resolution: 0.2mm Infill: 20% Notes: I've printed the model with a 0.2mm layer height (to print it very fast) and I've just done an infill of 20%, but it will bend a...

MP4 Model with mathematics. MP5 Use appropriate tools strategically. MP6 Attend to precision. CSTA Standards 4.2.2 Collaboration NGSS M.S. Engineering and Technology Standards Strand 1 Define a design problem that can be solved through the...

DesignThis is the reduced to the max case / housing / sleeve for the Raspberry Pi Zero (2 W) in the version with cooling (we have another model that is prepared without cooling), less is hard to imagine. A foldable print in place housing with live...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 0 pattern_line_thickness = 20 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_corner_radius = 5 custom_left_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...

... most of these parts. If there are any tweaks necessary let me know. I have added a .step file of the assembled printer and I will upload a Fusion 360 back up file as soon as its processed so you guys can go nuts customizing the solid models.

I made a small update to it, adding the model with the included screw threads in the back, and ever since that update the thing is still there but returns a 404 error for everyone who isn't me. I've tried to get it to post, I contacted thingiverse...