chompy from skylanders 3d models

ESP32 DevKitC (v1 or v4 tested)...

Update 08.01.2022: Added some examples for test patterns included in this model.Update 12.01.2022: Updated presliced gcode to make sure heatbed is turned on.Update 18.01.2022: Uploaded additional stl with text on test patterns describing its...

[ENG]Instructions for assembling a toy from 3D printed parts.  Material and supplies: Printed parts: - 1x head- 1x thorns- 1x front leg- 1x hind leg- 1x left body- 1x right body- 11x pin- 2x eye (left and right are identical)- 1x...

I'm just gonna show how to increase it, but I think by now the process for the opposite is also clear. Increase the height as much as you need. Use the tool “place on face” from the first step to put the part back in the...

This kit includes my attempt to depict the screen-canon Oberth class, alongside popular fanon variants of the ship from Jackill’s (Eric Kristiansen) Starfleet Reference Manual: Ships of the Fleet Volume 1, Volume 2, and Volume 3, as well as Strategic...

*Build can also be found on [PrusaPrinters](https://www.prusaprinters.org/prints/68735-prusa-slack-lack-enclosure)* --- **Purchase Parts:** * QTY 12 - 20x6x2mm magnets (used to secure the doors from unwanted sliding and opening) * QTY 8 - 6x50mm...

I created slope from the base of the tray to the lip of the tray so the cubes slide out more easily than the original design. The slots for the Blue and Green cubes are slightly wider than the other slots. These wider slots will fit 7 cubes side by...

So I can consider this bay as successfully working.Print instructionsI designed this with beginners in mind. I remember how terrible it is to have to remove each support from several pieces, and then discover that they don't fit together because my...

On the other hand, it is necessary to remove supports.  Print the following files:- Jupiter Vat Latch -Jupiter Vat Latch Base (left-rigth)You need (the pieces are only representations, do not buy these if you do not want):-Screw...

DAT has a 470Ω series resistor, and both DAT and CLK are bi-directionally level-shifted from 3.3V to 5V by TXS0102DCU, to meet recommended operating conditions for most strips. | Device | GPIO | Notes | |:--------:|:-------:|:----------------| |...

An exemplar of woven wire container designed for Customer Service Representatives (CSR) A specific type of wire-constructed basket intended to cater to the needs of Client Support Representatives (CSR) A unique variety of woven wire receptacle...

They have cutouts for zip ties.The V2 is lighter but weaker; I wanted to put some carbon strips on it additionally for strangth; normally just print the regular versionOptionalFC Cover Covers the FC stack for added protectionESC CoverCovers the...

TL;DRPrint in place fidget spinning finger ring in all sizes.  Giveaway As a owner of a 3D printer, you know the situation, that anyone who visits you to have a look at your printer, likes to get something printed from you. While you...

Those patterns are different from the first set, and can be used instead if the first one isn't printing properly on your 3D printer.The picture displayed on top of the page are showcasing the 1st set, the renders are done with the second set.The...

It is easiest if you start with the chain hanging down from the handle. Start spinning slowly, and then start to vary speed, and even reverse the direction. Speed changes should be gentle, because abrupt changes will cause the chain to jam and fly...

You can feel the initial resistance to the file from the ridges. Notice how, after a dozen light strokes you can feel that resistance fade ... you've knocked down the ridges. I then roll the part while it is on the cylindrical file and I file down...

I attempted to do a minor fix but had no luck and so just printed as is and it works great and the holes are not noticeable once the drawer is in place.At some point in the design process when I was cutting and merging the openlock parts to the...

With this converter, the fan voltage can be reduced from 12V to approx. 7-8V, so that the fans run quietly but sufficiently strong. To connect the fans to the voltage converter, I constructed a Molex adapter into which 4 standard straight 2.54mm...

it shoots about 30 feet, is pretty small and is made out of purely printed plastic and two rubber bands (One for the trigger and one for the magazine).It requires no fasteners, or glue, and just uses printed tabs to connect the clam shell case.It...

The rods are ⌀12mm.The center of the bearings on Hadley sit at approximately 70 cm from the ground, which makes for very comfortable viewing while sitting down. I recommend aligning the focuser as shown in the pictures, this makes a big difference...

* all protrusions from frame (filament spool, extruder, power connector) are on the right hand side to minimise desk clutter and allow the back of the BabyCube to be pushed right against a wall * Clean wiring. Include the wiring in the design,...

This is heavy.The relay bodies and caps were remixed from myyellowminicooper's designs here:https://www.thingiverse.com/thing:4303759Thanks to myyellowminicooper! Those designs were a great starting point for me.</p><p>I made adjustments to the relay...

... All at OnceSurface Mode: NormalExperimental Extra Skin Wall Count: 0Disclaimer: This model will look outstanding if printed on SLA/SLS 3D printer. The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.

Compatible with Smart Diffusers extension.Example of parameters from one family: Type CRL-400-R CRL-160-R CRL-315-R Air Flow 0.00 L/s 0.00 L/s 0.00 L/s Arrow 300.0 300.0 300.0 Arrow Distance 0.0 0.0 0.0 Arrow Length 50.0 50.0 50.0 Arrow Visible True...

Don't try to print the Panel lying flat, it will make the part unusable because the dovetail dimensions will be inaccurate and you won't be able to fit the parts together.No brim required for the rest of the parts.Bolts & Nuts should be printed with...

You can make the product on a 3D printer or cnc machine from plastic, glass, clay and any materials. the model can also be made using cnc machine turning wood.Also the model can be executions in castings. If necessary, I can make injection molds...

Insert the terminals to the bottom and glue them with glue to prevent them from moving.4º Solder the positive cable of the battery connector to the positive pole of the dc-dc converter.5º Screw the dc-dc converter to the battery connector with the...

Mount the switch so it triggers from a push of the shaft and then put a blob of glue behind it. Epoxy works really well for this. Notes: I printed all parts at 0.12 layers using a 0.4 print nozzle and PLA. The part tolerances are fairly tight...

*I used brims on: windshield front_hub_bolts front_glow_red back_glow_red axles 5 - The windshield prints well, however depending on your slicer settings/filament/printer, one edge may suffer from overextrusion. If this happens on your print, do not...

After redesigning the first time there appears to be a little bit more wiggle room and I could see even a rigid filament being able to get in there, and then once the top plate is put on it would take up the extra room and keep the mount from coming...