chocolate 3d model

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

Tolerences are tight on this model and will require percussive pursuasion to fit a 2020 bar Base - print with inside pointing up, support the central overhang, the Ports section print as bridged ### PETG: Top- print with the inside pointing up, this...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 0 pattern_line_thickness = 20 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...

The engraving starts at 1.8mm and the model continues at 2.2mm. Use contrasting colors for a clear reading. <b>note:</b> <i>* If you suffer from corner bulge / swell or an elephant’s foot after printing, carefully sand / deburr them. When...

This is a 1:50 scale model (metric) of a space rocket that transforms into a Mars base. (well, conceptually) Instead of building vehicles to transport pieces to build a base, it seemed more reasonable to use the whole spaceship as the future...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_y_position = 0 stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_mirror = 0 stencil_drawing =...

Don't go bananas with the size of your 50mm fan - there isn't a lot of room to play with; I'd suggest a slimline model for safety. - Print out your Bleh5, any (non-wobbly) material will do. - Note the picture above and glue it to your assembled...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_extra_port_corner_resolution = 8 custom_bottom_fillet_radius = 1.6 custom_left_port_corner_resolution = 8...

Note: The X axis part is for the current model of the Geeetech I3 Pro printer that uses a metal plate on the X axis to support the linear bearings and extruder holder. When I was assembling my Geeetech I3 Pro C printer, I was struck by the fact...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

The COMPLETE Dragonpeak Barbarians I bundle contains every model of this set, from the modular units to the heroes, the mount, the Pinup and the terrain piece! The people of Dragonpeaks are direct descendants of the Humans who lived in Aera under...

... Use your best judgement if you have more experience at printing. This is my first upload, I am still struggling with FreeCad. Hence, the models might not be the greatest so please be kind. Use at your own risk but they work on my printer! ...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 0 pattern_line_thickness = 19 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_fillet_radius = 1.6 custom_top_port_x_position = -10 use_mouse_ears = 0 custom_bottom_port_x_position = 20...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 pattern_element_rotation = 0 custom_top_port_corner_resolution = 8 custom_right_port_corner_resolution = 8...

Anser from Niklas: Hi Bas, take a look at Stefan’s video about filament drying, I learned a lot: https://www.youtube.com/watch?v=eqQRN9TUw08 You do need an active dryer, not just desiccant, but your Esun dryer might work (don’t know the model). Were...

I needed a quicker and simpler solution to perform these tasks so I could focus on slicing and printing actual models. What is more basic than some good old push-buttons? Feel free to remix it as you wish. It would be nice if you upload the remix...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_wall_thickness = 1.6 custom_back_camera_corner_resolution = 8 custom_left_port_corner_resolution = 8 custom_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_top_port_corner_resolution = 8 custom_back_camera_x_position = 0...

The following customizer options were chosen for this particular model. The best approach for any specific sign will ultimately depend on your unique needs, such as text requirements and the required appearance and functionality. line_spacing =...

You just have to have the right case respectively.If you use the original MK3S+ frame check out the version for the original Prusa frame.&nbsp;FeaturesWorks with Raspberry Pi 3 and 4Works with any type of Armor-style case that uses M2.5 screws. Just...

and Pause Layer = 2. How I Designed This Print on Window Screen This model was designed to have the printer paused at ~1mm to have the screen inserted. I made sure I made the frame thick enough to allow for multiple layers to be printed on each side...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_fillet_radius = 1.6 custom_top_port_x_position = -10 use_mouse_ears = 0 custom_bottom_port_x_position = 20...

To do this I went to https://3dp.rocks/lithophane/ sized it in model settings, and set it to Positive under image settings. I kept it flat since it will be used as the back of the bookstand. But while it's not in use it can also be used as a cool...

I considered adjusting the model but decided to leave it as is, as I'd rather have a more positive engagement that you can adjust to your liking than end up with one that doesn't latch in place securely enough. I'll leave this marked as a work in...

I design a Electronic Bay Cover with LED Light Just a little favour>>>Less then 10% of downloaded Models get a like.→ If you like the design, it will be nice if you click on the like button and maybe share your print.   Its a heavy redesign of the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_extra_port_corner_resolution = 8 custom_bottom_fillet_radius = 1.6 custom_left_port_corner_resolution = 8...