chlorine puck holder 3d models

This is a toy hockey puck for the Super Jock Hockey game from 1976. ...I didn't have an original so I guessed, works good with Super Jock.

I Made this Single Puck for 7" Vinyls. ...If you train a little, You can throw them on, they will self center.

Hockey enthusiasts, gather 'round and behold the ingenious little display pedestal designed to showcase those coveted hockey pucks in all their glory!

The puck prints without support if your printer is good at bridging, but it may not look perfect from underneath. It's recommended to sand the puck on both sides to get a uniform flat surface. ...Also attach some fabric to the bottom of the striker for...

Design a puck that glides on runners for optimal performance, using Rhino to create and a Prusa V2 printer for printing in PLA. Print 12 runners, ensuring holes fit snugly in the puck; insert six on each side. The runners allow a smooth surface for...

Puck to hold dual 25mm capacitors in the original 50mm cap clamp. ... V2 size increased from 51mm to 52mm, cap holes increased from 25mm to 25.5mm.

This stand is specifically designed to hold a standard-sized NHL hockey puck.\r\n\r\nJust print and start enjoying!

Options: • A Pencil Holder capable of securely holding at least 5 pencils • An Expo Marker Holder that can hold at least 4 markers • A Pen Holder that can securely hold at least 5 pens • A Tape Dispenser that holds and cuts a roll of scotch tape •...

Vacuum holding pucks for holding down projects in a laser cutter bed. There are inserts for 5mm x 20mm bar neodymium magnets so that these can rest on the bed. 1/4" TRIM-LOK rubber cord fits the sealing surface. 6mm OD vacuum tubing for...

In this file there is 1 hockey stick and 1 puck. ...If you lose the puck you can always print another one (This happened to me a lot). You have to print 2 hockey sticks for the full set. Perfect for playing on a desk. ...Nets coming soon.

Tabletop or shelf display for your hockey pucks. ...Designed to showcase the puck upright and with as little distraction as possible  Should be ok to print with as little as 5% gyroid infill.  No supports necessary. 

A real ice hockey puck with the exact measurements of those used by professionals in the National Hockey League would make for a fantastic decorative item. ...However, it's also incredibly enjoyable to glide this puck across a glassy surface as its...

I created this to prevent my Lansky Puck Sharpener from scratching other items in my bag.Fusion 360, STL, 3MF & STEP files included.Use STEP files for the best printing speed and quality.Designed for this Lansky puck sharpener:...

STL's requested by Redditor: https://www.reddit.com/r/oddlysatisfying/comments/rvbayn/does_my_3d_printed_puck_game_count/ Print 10 pucks (I recommend 100% solid) Print 2 boards Print 1 midpart Some kind of elastic band required (1mm thick)

There are several similar puck designs available on Thingiverse, but most require overkill screw mounts. This design uses a thumbtack or small finishing nail to secure the top, keeping pucks lightweight. ...The model was created in Tinkercad, and I'm...

Experiment with the design of your hockey puck using OpenSCAD by adjusting its internal rollers for off-ice practice. Recommended RepG settings include no additional shells, a 0.2mm layer height, and 100% fill, while utilizing only external supports....

If you have bough the EZCO puck charger for your Garmin Vivoactive 3 / Fenix 5 5S 5X / Venu Sq / Forerunner 935 / Approach S60 X10, and your like me, it's kind of hard to aligned the connector on the puck with the watch. So I've created a small...

The player who hits the puck is trying to get it as close to the opponent's feet as they can, while the other player is trying to avoid getting hit by the puck. The game continues back and forth until one player successfully hits the puck into their...

I found that the pucks get stuck inside the porta filter and had to hit it fairly hard on the knock box, to avoid damaging my kitchen counter I designed these items to simply push into the porta filter and loosen the puck, then remove and tap on the...

... height at 0.2mm with supports proved to work amazingly well! I'm really pleased with how it turned out. Also worth noting is that it's crucial to print these jacking pucks at a 100% infill density in order to ensure maximum strength while lifting.

I was inspired by the puck from fflood http://www.thingiverse.com/thing:39864 but wanted something that could print with minimal supports so I took the concept and redesigned one from scratch based on a puck that I have. Enjoy! Update: Even at 85%...

This is a basic Painter's Puck to allow you to easily clean your brushes. Simply run water and scrub your brush against the nubs. ... Printing Tip: Use 4 walls for strength otherwise your nubs may break off.

Approximately five inches in diameter and three inches tall. ... I printed mine with black PETG at .20mm layer height.  Unfortunately I have a damaged spot on my print surface and it shows on the top of the puck.

I designed a hockey puck for my son that he could use inside without making any marks. It has a TPU sealing that makes its edges soft. ... Requires: 1xM3 bolt and nut

We watched a video where Devon Montes built a Plinko Puck and were inspired to create our own. ...As a company, P&M wanted to replicate the fun and excitement of having one in-house.

I engineered a light source combining elements of a diffuser and a table lamp to complement my set of handheld LED Puck Lights. ...These wireless devices were sourced from Costco and operate under remote control.

I'm not familiar with that emoticon, could you explain what a "hockey puck" has to do with smiling? I think there might be some misunderstanding about how emoticons work. ...🤔

To assemble the pucks, simply glue the images or write the Amiibo name, insert the tag, and secure the lid to the puck with adhesive. The custom Amiibo card designs used in these projects were obtained from GBATEMP posts. Full credit goes to...

RELEASE THE KRAKEN! ... This NHL sized hockey puck features side text and texture as well as the logo on the top face. ...The coaster is a standard 4" diameter.

A detailed three-dimensional representation of a sleek black hockey stick and puck is now available for use in various software programs, including 3ds Max 2010 and its later versions, as well as numerous other compatible applications.