char 2c 3d model

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_pattern_thickness = .8 custom_back_extra_port_y_size = 30 custom_back_camera_corner_resolution = 8 custom_top_port_x_position = -10...

I probably should make that easier to do if when printing the full model instead of the slices (maybe an exercise for the one wanting to do that - add a better wire hole). I used a 2.1 bluetooth stereo board that I got on ebay for about $21...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_wall_thickness = 1.6 custom_back_camera_corner_resolution = 8 custom_left_port_corner_resolution = 8 custom_corner_resolution = 8...

The "Advanced_Fit" version is meant for printers with tighter tolerances and may provided better heat break cooling due to the extended cooling channel.** After looking at all the options for a hotend mount here on Thingiverse and Facebook i decided...

**My Tinkercad-works:** [Coverplates + Hinges + Z&Y-FrameChainmount + Connectos-Hub + cutout-stamp](https://www.tinkercad.com/things/60ksBr4wvsb-s8-pro-coverplate-hinge/) [Hotend Mount + Y-Axis Chain...

This model was almost perfect, but when I printed one out, it turned out to be a bit chunkier than I really wanted. So, I figured I'd take my own shot at it and came up with this. My requirements were: * It had to match an authentic full-size...

All necessary supports are pre-applied to the models (there is no need to add additional supports). The main body of the stein/mug prints with cylindrical supports, the left/right lid have perforated supports, the lid top doesn't require supports...

*Note: don't order a GearVR with a white body - it is a 2015 model with smaller lenses that don't fit.* **UPDATES** **V3.3** (slight comfort improvements over v3.2). [print 1 for each eye] **Added a version for the prescription inserts from VR Lens...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

This meant adding three holes for screws, and I also added flanges on the bottom in an attempt to mount the fan shroud I modified for my model cooling fan shroud. I left the sensor port alone for now - I may or may not try using the cooling fan...

I have completed assembly and everything works so this addresses some of my main wants for this awesome model. I am also going to include the full parts kit here (the originals I used also), so everything you need is in this one thing saving any...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 use_stencil = 1 stencil_shape = 7 stencil_size = 40 stencil_mirror = 0 custom_back_extra_port_x_size = 30...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_shape = 7 custom_bottom_port_corner_radius = 5 custom_back_camera_y_size = 20 printer_tolerance = 0.4 stencil_pattern_line_thickness = 30...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...

the better the less likely it will grab but u can always use nuts on the other side even tho i didnt make a place for them to sit on the model since i had planned on using the threaded inserts but it will still work cause thats how i test fit...

Because of the simple geometry of the Box and the Pieces, these modest settings produce a very nice model in a relatively short print time. Please Note: Although I have not provided the solution here, I will respond to personal Thingiverse messages...

My Fusion 360 CAD model has 0.09mm of axial clearance so the printed threads should effortlessly spin together. Extruding over 0.09mm will make it extremely difficult to twist the nut and bolt together using fingers, so just reprint both parts with...

I haven't printed it yet, but the OpenSCAD model turned out pretty well. See the additional .scad file, .stl and the explanatory symbols image. The original bezel is dark grey with a textured interior except for the plinth and label obrounds. This...

Find it according to your vacuum cleaner model. In the file, you can also adjust all necessary parameters, including the angle for the vacuum cleaner adapter. Copy these values into the snipper file as well, since the first section's angle is needed...

... with any light color and use a permanent black marker for the text. These models are not designed for dual-color printing. You'll need to print two Monster Ability Card holder v1. ...One is for the Monster cards, the other is for the shop cards.</p>

If you need to use a different pump you can model and print your own adapter as it is just a rectangle block with a hole for the pump water outlet. The inlet block should be 80mm tall and 32mm wide minus half a millimeter for fit tolerance. If you...

This is an second version of my first remix/modeling effort. Here is a <a href="https://www.thingiverse.com/thing:4714457">larger version that utilizes 4 magnetic bars</a>. <b>Principal changes in this remix:</b> <ul><li>In lieu of the...

--------------------------------------------------------------------------------- Print Settings: • Ensure the model is orientated as shown in the slicer image • Skirt - Yes • Skirt Line Count - 2 • Skirt Distance - 1 mm • Support - Yes • Support...

READ BEFORE PRINTING!This is a non-commercial print, this means you are not allowed to sell files or prints of this model.______________________________________________________________________________________What is this?A modular tripod/handle...

The bowl model is a solid piece, and CAN be printed in vase mode / spiralize outer contour. This, however, isn’t the strongest. What I do is print them with 0% infill, 2-3 outer walls, 4 bottom layers, and 0 top layers. Basically makes it a double...

It can support itself and needs a lot more force to be bended. If you still want to print your own loc line, I used the models from MinyMan644 found here -&gt; Loc-Line Fittings (1/4", 1/2" and 3/4"). I strongly recommend buying loc line instead of...

As far as assembly is concerned, it's all pretty self-explanatory when you see the models, but here are a few tricks: Use as little wire as possible, but make sure you use good wire. The wires run from the grip and back, across the side of the...

The hole for the cable tip should be wide enough for any similar cables, but if not you can pretty easily remix the model by just cutting the hole to be larger or adding material where needed. I suggest printing the dock upside down and including...

Currently, there are three models:Ebook Reader Holder (1x3):This was designed for my Kindle Oasis in its third-party case (if you want it for something thicker than ~15mm, let me know and I'll see about whipping you up a variation)1x3 footprint on...

(You may be able to get away with shorter bolts but these were the only ones I had that would fit) I have included a thumb screw model to make it easier to open and close the cover without a wrench. You will need an M3 heat insert but I cannot stress...