chapulin colorado action figure 3d models

With the new Pokémon Let's Go games being announced, I figured this was the perfect opportunity. Disclaimer: The Switch logo is a trademark of Nintendo and the Poké Ball is a copyright of the Pokémon Company. I don't claim ownership over either one....

I will release more 'patterns' once I figure out a good way of laying them out. The basic open grid is fairly strong as is though; the 3x3 cube can hold my full bodyweight (approx 75kg/165lbs) so full reinforcement is not necessary except for very...

I also added the motor firewall with lock parts, and I'm still figuring out the front direction. Here's a small video on how to mount the kit: Next step is finishing the front direction and then making a list of hardware. ...

INTERIOR HEIGHT MINIMUM NOTE: To figure out interior Height of your enclosure, take an EVEN number of Units (U’s) you want to use, multiply by 1.75”, and then add 0.625” to cover for clearance of the finished top and bottom. For example, if I have...

I figured out a simple solution to this issue. While your Nintendo Switch and your Pro Controller are held together by the 3D printed mount, go to the settings on your Nintendo Switch itself (not in a game). Scroll down to where it says "Controllers...

I had to figure all that out, and I can save you some time. I've not uploaded Arduino programs before, and they seem kinda tricky because they have all sorts of files and whatnots. Build and use at your own risk... you know you want to! Print...

If you're concerned then figure out your balance point and cut the threaded rod a bit shorter than that. Update: 19/6/2017 I have now developed a bearing hinge that uses a couple of 608 bearings (Roller skate bearings). The files for the bearing...

I make no promises that it will be sized right for any 5-pack of 1¼" fuses, but my suspicion is because the Eaton Bussmann fuse pack has been around for so long (there are lots of people on eBay and other aftermarket marketplaces selling empty packs)...

I figured if I didn't want it running, I could just unplug it. The potentiometer gives me a small amount of control over fan speed, less important with a 5V supply but still nice. If you plug this into a 12V supply, you'll really need some control as...

You need to figure out the IP address your router assigned this device but once you get that, you simply go to http://yourIPaddress and you can start adjusting things. Tip, When you first connect the matrix LED array, it will only partially...

It took some thought to work out how to do that without having to re-do the design from the start, but I figured that out and have now made that change. Specifically, where the form contacts the print bed the clearances between the rings is not 0.4mm...

I figured out after I was done that it would be easier if you print a second piece that is only the one face of the mounting case that goes against the wall, so I have included that template. Print it slowly so the holes are good. 3) Push that...

The coating absorbs loads of the blue light and emits it in a full spectrum.I'm not sure if the red strip really does anything here, but I figured it won't hurt.Now glue the strips on the aluminum profile and leaf 20mm on one and 15mm on the other...

So careful understanding of any nearby metallic objects is important (power lines, telephone lines, gutters, metal roofs, other antennas, ...etc) :...

I'll get better instructions on how to put them together and take them back apart eventually - but its not that hard to figure out. Print Settings Printer Brand: Prusa Printer: Prusa Mk2 Rafts: No Supports: No Resolution: 0.2mm Infill: 15% Notes:...

In the first design I figured to put two stacks vertical in there, but I made a mistake in the size. A box is better suited for the scribes as they are resources-type of chit.</p> <p>Update 11: TheoKyle will be rewarded the "first make" posting with...

I just figured I'd dump this thing online, but I realized I did this in a pretty messy way and would've felt bad if someone messed up their caliper. ...It's all very straight forward and I may revise this one day if I care enough to do it.I'm sure...

If it fails, try to figure out why and share with the community so others can avoid that mistake, fix it, repeat it, and learn from it. There's a video about how I came to make this thing and some clips of it gliding on YouTube:...

----------------- Updated 8/22/2021: Somehow the head was uploaded incorrectly (I cannot figure out how it happened). So, head_fixed.stl replaces head.stl ----------------- Enjoy! ...

In the past for these puzzles you have to first figure out how to put the two tubes together by following the maze. Then you had to reverse the procedure to separate the two tubes. This resulted in working the maze twice. In my design the tubes go...

I figured out how to do that without having to re-do the design from the start, and have now made that change. Specifically, where the form contacts the print bed the clearances between the rings is not 0.4mm wider, with that extra clearance tapering...

I wish I could figure out how to show a video - this thing moves constantly as you print - proving the fact that there is a lot of tension in the line that should be absorbed and not transferred to the filament. [If you want a heavy seas dual rod...

I figured I'd give a whack at designing something in Fusion 360 to help this issue. The goal was to make this as easy to make as possible, if there are any improvements you think that can be made, please don't hesitate to comment. # Warning ...

It recreates the complete Palace.1:12 scale (6 inch figures) This is Set #9a Rancor Cave Attribute which includes- The Blender file- Build instructions - With Print instruction for layer height for each part - Paint guide for all parts - Assembly...

Rather then make a mess attempting to print fine rod ends, I figured using filament would be a simpler and easier method to get the same result. There is a peg on the bottom that inserts into the main body for mounting. - Barrel Shroud, Rifled...

Since the only time you ever need those sliders is when you're first setting up, I figured that was good enough. But your mileage may vary. There's still room for one more 251mm x 97mm x 13mm tray. I do have a few stray monsters for the various...

----------------- ¹ I returned the M2 because I felt it had too many flaws to justify it's high price tag ($60 in Australia), and I figured that since I own a 3D printer, I could probably design and make my own head-strap without the flaws of the M2...

4mm, mounts to the plates from Keyport's Maker Kit with 4mm torx screws which they ship with the kit; the result is, in my opinion, great, as the faceplate is thin, slick, and you can have up to three RFID fobs integrated in your Slide (the faceplate...

Not a good combo. The monitor is a Dell P2314H and the size of the pole is about 70x40 mm. Started thinking about attaching it atop of one of my monitors and found that the upright of the monitor stand seemed fairly sturdy so I figured i could do...

I had some wood filament that was getting old so I figured I would try replacing the old white covers with some cedar ones. There are quite a few of these already available but I though I would design my own for fun. I was quite surprised how well...