chain mount 3d models

This is a filament sensor mount, filament guide, and cable chain mount all in one for the Ender 3 printer. I've modified this filament sensor design to accommodate a bowden tube that will guide the filament through it. To begin with, use either the...

NG_Design's cable chain mount remixed with Tobi0892's cable chain link to allow compatibility between the Tobi0892's cable chain design and NG_Design's screwless mount. Unfortunately a small support is needed under the chain attachment area. I did...

This design is a straightforward cable extruder/cable chain mount that complements my previous carriage mount creation. It seamlessly integrates with parts crafted by LordFelix93. To access this design, please visit the following link:...

Another cable chain mount for the X-axis, its design is significantly smaller than the original version, allowing the printer to fit perfectly into an IKEA Lack printer table, with added stability. The most crucial aspect is that this new mount...

... with a 90-degree bend to guide wires around the corner without letting them sag down and rub on the chain support. Added ChainEnd_In_Stepper, which has a small cutout to clear the stepper chain mount while keeping the stepper chain mount the same.

This modified version of the hotend side chain link mount boasts enhanced durability. I tweaked the original design to address its weakness where it gripped the carriage, which often led to breakage. Thicken this critical area and you'll end up with...

New holes are required on the chain to mount it onto the bracket. You also need M3x10mm screws, washers, and nuts for mounting on the Z-axis mount. ... I drilled a 4mm hole on the opposite side of the cable chain and attached it to a vertical 2020...

Le projet originel de FedorSosnin est accessible à cette adresse https://www.thingiverse.com/thing:3643366 Le projet originel de K Sims est accessible à cette adresse https://www.thingiverse.com/thing:3561563 ---------------- [English] Mixing of the...

The X carriage extension is for the LPA Modular X carriage at https://www.thingiverse.com/thing:2034743. [Update] I created a shorter mount and this will give the full 200MM Z height. Use the "Short Drag Chain X Motor Mount With Channel.stl" file....

This design serves as a drag chain mount for the Tevo Tarantula. The drag chain is 10X20. The X carriage mount fits onto the modular X carriage from thingirob at http://www.thingiverse.com/thing:1438795. The motor mount features a channel and fits...

Current issues: The PIP receptacle is fragile due to design, so be careful Mounting of the lower male section needs to happen at the lowest 2020 extrusion Update 12/10/19: Fixed a mesh error in the chain mount Update 12/15/19 Uploaded a new version...

I am really new at this 3d modeling and I used blender to merge the two STL's to make a v-slot chain mount for the Ender 3 Max. I liked JohnnieWhiskey's v-slot mount but the angle of the chain connection was awkward for those cables that run by...

The linear chain mount was relocated back to provide straight access to the screw that adjusts the Z height, and it was raised by 1/2" because it seemed too low compared to the extruder mounting position. Additionally, I gave it a little extra space...

Separated in to 2 piece for easier printing. ... To be used with cable chain system from https://www.thingiverse.com/thing:2920060 Hotend mount 0.2 with supports

A mount for johnniewhiskey's Ender 3 cable chains that attaches to the EZR extruder. ...I'm using this to go from the extruder to my hotend.

I required a custom mount to connect my cable chain on the motor side and X-carriage so that it wouldn't interfere with "The Hulk" supports. These mounts will shift the cable chain towards the back along the Y Axis. ...You'll need to detach your...

... the left side Y axis mount. ...At least for me, after a couple days, the bracket mounting the cable chains began to bend. Reworked it to integrate the motor bracket into the cable chain bracket, added gussets, and a thicker top. ...Much stronger now.

... links. Parts Description 20mmx10mm Drag Chain Compatible drag chain M3x5mm Brass Inserts (2) Motor Side, (2) Frame Side M3 Flat Head Bolt - 8mm (2) Frame Side M3 Flat Head Bolt - length varies (2) Motor Side Go here for more info and good parts.

... clamp and compatible with Nema 23 motors. ...Two variations are available - one using a single chain and the other employing a double chain. ...All components required can be found at Thingiverse under this link: http://www.thingiverse.com/thing:11978.

remixed this to mount a chain on the Hotend from my A20. This is a remix from https://www.thingiverse.com/thing:4738946/files. You can use the chain from johnniewhiskey https://www.thingiverse.com/thing:2920060 It works perfekt at my A20. ... Maybe it...

... LowRider CNC from V1 Engineering. ... Comes with clips that slip onto the aluminum tray to hold up the drag chain. Drag chain was bought on Amazon link -> https://www.amazon.com/gp/product/B074XXZF4D/ref=ppx_yo_dt_b_asin_title_o09_s03?ie=UTF8&psc=1

I remixed this to mount a chain on the Hotend from my A20. This is a remix from https://www.thingiverse.com/thing:4738946/files. You can use the chain from johnniewhiskey https://www.thingiverse.com/thing:2920060 It works perfekt at my A20. ... ...

Mount a drag chain on your CNC machine, securing it to the Z-axis. The chain needs to be attached directly to this axis for optimal performance. ...Ensure a secure connection is made to maintain precision and stability in your CNC operations.

Loved the chain on my Ender 3 so I printed it for the CR-10. ...Since the rails are a little different on the CR-10 I moved the mount to the back.

This a simple mount for a 10x20 drag chain for the Sapphire Plus Corexy 3D printer. You will need longer M5 screws to mouth this. ...About 4-5 mm longer will work fine.

This is a bracket that will mount up to the x axis exo-slide, which will allow attachment of a 10x15 cable chain for the extruder and hot end wires etc.

I reworked the chain from my Ender 3 and successfully printed it for use on the CR-10. ...Given that the rail configuration differs slightly on the CR-10, I shifted the mount towards the rear.

I wanted a cable chain that wouldn't limit max print height, which is currently restricted by the LCD nob but will be moved to the front like on the Prusa MK2. ...I designed a suitable mount for it.

This set up works with an Ender 3 with Micro Swiss NG Direct Drive extruder. ... Used cable chain by johniewhiskey. The mount by FedorSosnin also works with the Micro Swiss NG carrige mount. ... The base for the mount came from MSergW

Goes along with the hot end carriage mount. ...Basic design to allow for use with an Ender 3 pro that has the XZ ExoSlide kit and mount the cable chain at an OE bowden extruder location. ...Printed and in use.&nbsp;</p>