chad model guy

UPDATE 09.08.2022 •changed length for diffusor and mount from 10mm to 100mm •orientation changed for some models •added end cap UPDATE 12.08.2022 •added with diffusor / without diffusor comparison photo and electronics box wiring photo •added...

The Tunnelplan Wind Turbine is a 1:10 scale model of an existing wind turbine. The diameter of the rotor is 2000 mm (20 meters) and the tower height is 1200 mm (40 meters). the max.ceiling height inside the house. Solution 4 energy...

Moreover….Sitag astonished me a lot because actually….they continue to make and sell the same model: the famous “Sitag Reality”…which costs now around 700€ !!!Therefore, I decided to try a repair with my engineering skills and a big dose of...

 READ BEFORE PRINTING!This is a non-commercial print, this means you are not allowed to sell files or prints of this model.______________________________________________________________________________________What is this?This is my fifth...

UPDATE: The model has been printed & test fit. Like a freakin' glove. #caliperlove Inserting the letters requires a bit of finesse & just enough brute force not to break the R and X apart- just be patient & make sure to clear any wisps/stringing in...

Filament Dry Box (Peli Case) Storetwo standard 200mm filament spools in an air-tight Peli Case. Perfecting for storing your hygroscopic filaments after drying. The Dry box can be configured to simply store the filament, or by drilling and tapping 4 x...

Enable the Rotate_For_Printing option to rotate the part in this orientation. Supports: Depending on the options selected, it may be necessary to use supports. Rafts: Doesn't Matter License The "Sidewinder X1 FFC Riser" models (.stl) are licensed...

NOTE: Newest v2.0 of this model is now available - click here.NOTE: This is v1.1. If you were looking for v1.0 - click here. Note: As of Nov 16, 2023 — in addition to the earlier remix changes, today I added SVG files for engraving the plexiglas...

I recommend 8 IKEA LADDA AA cells as they are amongst the best available anywhere (https://www.ikea.com/us/en/p/ladda-rechargeable-battery-70303876/):https://cults3d.com/en/3d-model/tool/aa-six-cell-battery-holder The one piece parts need a big...

To prevent that, don't hesitate to rotate horizontally one the stack 90° clockwise or counter clockwise, to prevent symetric parts interlocking each other.More than two player can play together if another set of tiles is printed.The printsThe 3D...

Make sure to follow me to get a notification when it's uploaded!*** ------------------------------------------------------------------------------------------------------------- ###READ BEFORE PRINTING!### * First of all, this is a non-commercial...

**Update 2022/04/08:** Fixed a bug in main body model. It was slightly to long on left bottom side to fit nicely over the antminer case. This project aims to convert a Bitcoin miner into a handy space heater. **We achieve this by:** *...

The VR Box comes with pads that may fit your need here. Even if my model provided screw holes and additional holes to fit the screwdriver through, I do not recommend using them. The pillars the screws were originally drilled in are most likely...

I just have to choose a bulb of the wattage I want and with a high CRI to get the best image quality.Since Fresnel spotlights are a classic in the world of cinema, I based my project on a model of the Arri brand from the 1940s. Which has a spindle as...

A big thanks also to Eric Clinedinst who helped me to find the first issue. This is the BOM list for the internal part: 1x 5x10x4 (MR105z) Bearing for indirect filament sensor 1x round neodymium 8x3...

The airflow is higher than stock and the Draken due to its duct design but it has more channels.The main point of developing the Gripen next to the Draken is for printing models that need less but more controlled cooling, meaning it cools from all...

EX6 Arcade Fight Stick What started as just doing a few tweaks to an existing model turned into a near full redesign and a (almost) fully printable arcade/fight stick case platform; the EX6. Printable on the Ender 3 or any 200x200 printer. The...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_back_camera_x_position = 0 custom_top_port_corner_resolution = 8...

Update 220811:Added solid with 1deg step on requestReplace the code below to this, (BB and CC changed to 2 and 1 and replace STL to the new...

If you are using ceiling pipes, I've modelled the right side of the pipes only. For the left side it will need to be mirrored in the slicer. The vents part is optional but I recommend glueing it to the roof. The vents piece can act as additional...

The COMPLETE Order of the Labyrinth bundle contains every model of this set, from the modular units to the heroes, the mount, the Pinup and the terrain piece! The strong Minocs of the Order of the Labyrinth are the descendants of Tesevros the Wise,...

Merci de me faire un retour si vous rencontrez cette situation ====================================================================== __English__ ##Removable dust collector for CNC Carbide 3D Shapeoko## I made this model to have better access to the...

You may need to adjust your switch's orientations in the holes depending on your model of keyboard switch, so be prepared to work through that. 13) Lay in the keyboard-switch-populated 3D-printed piece so that the pins face towards the inside of...

Wandering hour clocks have been around since the 1600s, but this one implements the concept in 3D printing!This example uses the case, dial pan, glass, and movement from an IKEA BONDIS, but the model could be scaled on the X/Y axes to fit almost any...

If you do this, make sure to account for the thickness of these things to ensure that everything ends up flush as it should be. I've included a Sketchup model with more information, like joint lines, as compared to the .stl files. ...I will post more...

No support is needed and would be very hard to remove because the support would be inside the model where the magnet eventually slides into. We are depending on bridging for the parts that would normally need support. I have given extra tolerance...

Supports are built into the models. The fan shroud should be printed with the blower mouth facing up. Trim off the bands tying the barbell studs together and remove the two pieces that support the shelf at the rear.</p> <p>Some good print settings...

(In the future, I'll model a printable screw-gun interface for people who can't get the part in question.) 4.#6-32 brass nut, 1/4" across (measured face to face), 3/32" thick (optional) McMaster-Carr 95130A120. Fits into a pocket on the gun carriage,...

If you want it with an internal battery, I have designed this same model with a hole for the battery, measuring 126x85x35mm, you have it here: https://www.thingiverse.com/thing:6016217 Required Components: - 1u Mini ZVS Module 5-12v (...

They are used to mount the armsSolidWorks BOM (approximate, since you will not use everything in the model)M3x10 flathead: 22 (for top and bottom)M3x10 socket head: 16 (for motors)M3x13 flat head: 8 (for arms)M3x12 or longer socket head: 4 (for...