ch 926 3d models

Here's my interpretation of the 20" BBS CH-R wheel. I've incorporated it into an ongoing project - a customized Volkswagen T5 DUB-Edition. To ensure a seamless look, I've designed a standard tire profile specifically for this wheel setup. ...Feel free...

My CH Pro pedals have been sliding on the carpet for 2 decades, so I finally got around to fixing it after getting into 3d printing. Talk about procrastination!Print 2 for the front of the pedals and it works very good. ... Print for front and back and...

CH-47 Chinook Japan Air Self-Defense Force Technical Notes: Cinema 4D R10 format comes with materials and textures. Other formats include textures too. Polygons Total: 45232 Vertices Total: 46418 This model is an artistic representation of the...

I printed a box for my hiking trail ideas cards.CH Hiking Idea Cards are stored in this box. ...I printed the box with these dimensions: card_width = 132 card_height = 195 box_depth = 120 card_spacer = 2 box_wall = 1 box_separator = 3 Customized...

This is a direct replacement throttle, mixture, or propeller lever designed specifically for use with the CH Eclipse Flight Yoke. ...The lever offers a precise fit for the propeller and mixture control knobs, while the throttle knob provides a slightly...

... larger cut outs for USB and the lever and it gently forces the programmer into a stable position in the enclosure. I also made a small box for the CH 341 and its accessories, which you can find here: https://www.thingiverse.com/thing:3463316

If you like the model please rate it.The CH-47 Chinook is an American twin-engine, tandem rotor heavy-lift helicopter. Its top speed of 170 knots (196 mph, 315 km/h) is faster than contemporary utility and attack helicopters of the 1960s. It is one...

If you like the model please rate it.The CH-47 Chinook is an American twin-engine, tandem rotor heavy-lift helicopter. Its top speed of 170 knots (196 mph, 315 km/h) is faster than contemporary utility and attack helicopters of the 1960s. It is one...

If you like the model please rate it.The CH-47 Chinook is an American twin-engine, tandem rotor heavy-lift helicopter. Its top speed of 170 knots (196 mph, 315 km/h) is faster than contemporary utility and attack helicopters of the 1960s. It is one...

If you like the model please rate it.The CH-47 Chinook is an American twin-engine, tandem rotor heavy-lift helicopter. Its top speed of 170 knots 196 mph, 315 km/h is faster than contemporary utility and attack helicopters of the 1960s. It is one of...

If you like the model please rate it.The CH-47 Chinook is an American twin-engine, tandem rotor heavy-lift helicopter. Its top speed of 170 knots (196 mph, 315 km/h) is faster than contemporary utility and attack helicopters of the 1960s. It is one...

If you like the model please rate it.The CH-47 Chinook is an American twin-engine, tandem rotor heavy-lift helicopter. Its top speed of 170 knots 196 mph, 315 km/h is faster than contemporary utility and attack helicopters of the 1960s. It is one of...

I got a CH Throttle Quadrant for free with a broken lever, so I made this replacement. When I printed this, I selected the "Outer Before Inner Walls" option to keep the external dimensions as close as possible. The fit of the lever is very tight,...

Bar chair CH-5032/Cup measures up with impressive dimensions. Standing tall at a maximum of 82 cm and as short as 70 cm in general height, this chair commands attention. From floor to seat, its height ranges from 53 cm at its highest point to 44 cm...

Our official Army TASC training aid CH-47 model at work had broken "blades" (the plexiglass discs). I modeled these to be printed flat and the spindle can be screwed or glued to the blade hub. ... They were originally a little more accurate to life,...

This is a handle tie for a Type CH Breaker. The part it replaces is: CHHTCS. I received a brand new breaker from a supplier with a broken handle tie. I didn't have time to replace the entire breaker or order a new handle tie (for ~$10) so I...

I have a shallow desk depth, which is why my CH Pro Pedals are not ideal since their cable comes out of the back, getting pressed against the wall. Two little feet attached to the pedals with 1" double-stick tape will protect the cable and the wall.

The CH-7, a Chinese CASC UAV, boasts high-altitude, high-speed capabilities for long-duration reconnaissance and strike missions under intense conditions. This stealth aircraft is designed for surveillance and combat purposes. As for the 3D model, it...

The nut is to tighten a standard bolt into the bottom of the CH yoke's foot holes if you get a 2nd hand yoke and they neglect to give you the mounting hardware. The 6mm x 7.5cm Carriage bolt I used has a round head and a square tightening area...

Using the following options: font_narrow_widen = -4 lug_length = 5 lug_width = 5 outlineextruder = extruder1 minimal_color_layer_thickness = 0.6 bar_color = Khaki border_width = 0 font_with_style = outline_color = Gray line5 = line4 = line3 = line2 =...

This 3D Chinook CH-47 model boasts 1,044,391 polygons and 1,062,424 vertices, including textures and materials. The detailed design was originally crafted in Autodesk Maya 2013 and rendered using KeyShot software. The Maya zip file offers both...

A 3D Model of BBS CH-R Wheels. This high-resolution model consists of two main parts: the wheel and center hub, each meticulously crafted to provide a realistic representation of the original design. The total triangle count for the entire model is...

The Sikorsky CH-54 Tarhe is a twin-engine heavy lift helicopter designed by Sikorsky Aircraft for the United States Army. The helicopter is named after Tarhe (his nickname The Crane), an 18th century chief of the Wyandot Indian tribe. [1] The...

Since the CH Products HOTAS has no Mounting Screws, I used some Cable Ties to keep them in place on the Mounting Plate. For the Prints you need a 200x200mm Print Bed! There are Build in Supports for better Printing Results. +++++ Updates +++++ ...

This is a very simple add on detent for the CH Pro Throttle. I designed this because I've been playing Falcon BMS a lot and with 4.35 I had a lot of trouble knowing when I was in burner. This detent is just a push through, no finger lifts or...

This is a very simple add on detent for the CH Pro Throttle. I designed this because I've been playing Falcon BMS a lot and with 4.35 I had a lot of trouble knowing when I was in burner. This detent is just a push through, no finger lifts or...

Boeing CH-47 Chinook

Luminaire ARCANUM CH DUO

Customized version of https://www.thingiverse.com/thing:45576 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=45576

I'm afraid I don't have a description to provide.