cetus mk2 3d printer

If you're using the TinyFab CPU, which is necessary to use 3D touch on Cetus, then you can apply below settings to get the 7 point grid leveling. leveling-strategy.rectangular-grid.enable: true # The strategy must be activated in the config, as...

Complete set of STL files required to make an MK2 Clone 3D Printer - revision 1 (r1). Overall cost of build: ~200 USD + cost of printed parts. The cost can be higher if you use more expensive parts, such as stepsticks (TMC2100/TMC2208 instead of...

The Z-axis break for the Cetus3d MK2 had to be reworked by me, as the original part provided in the .zip file was excessively large.

It's an adapter for the MK series Heatbeds and the Print Rite 3D Printer. Original bed is 21 x 21 cm; MK3 bed is 21.4 x 21.4 cm. To involve cutting 1cm from the corners of the original Acrylic bed, which I'll be able to post pictures for later on. I...

A compact 12mm inductive proximity sensor mounting solution engineered specifically for the Cetus 3D printer, optimized by installing a high-performance tinyfab CPU upgrade.

This is a custom hotend mount for the Cetus 3D MK2, carefully paired with an E3D V6 hotend featuring a threaded mounting system. As of now, it remains untested, but upcoming experiments are planned to thoroughly verify its performance. ...To utilize...

Print Settings: Printer: Cetus 3D Rafts: No Supports: No Resolution: 0.2 mm Infill: 30% Post-Printing Instructions: Assemble the mechanism by using a spring from a pen. Insert one M2x8mm screw. Install two M2x5mm screws. To assemble to the printer:...

Cetus 3D z-axys Security Lock Switch Modified, print without supports

The Original Prusa i3 MK2 3D printer has a solid model design by Joseph Prusa Jr., with all parts licensed under the GNU GPL v3. ...To access the STL files for printing, visit the original source at...

... with the Cetus 3D printer. To generate the STL file, click on the link to open it in Customizer. For the 20*20 extrusion used as the spool holder for the Cetus 3D printer, you can leave the default values unchanged and it should provide a snug fit.

Angled adapter mounts a 60 mm fan on the Cetus 3D printer securely. The original air deflector attaches to this part with two short M3 screws, utilizing its lower two holes effectively. ...This adapter is mounted onto the printer using one longer M3...

Cetus 3D MK1 Initial Type Filament Feeder Guide A critical component is a bearing with an inner diameter of 3 mm, outer diameter of 7 mm, and thickness of 3 mm. Unfortunately, ABS printing is necessary for the initial prototype. Please print this...

I crafted these custom LRFs (Little Rubber Feet) to seamlessly fit over my Cetus 3D printer's existing small rubber feet. Using flexible TP filament, I printed them with precision and care. With a generous infill of 20%, they effectively dampen the...

The majority of the script is credit to @jeremyalangreen Added a rest area for a filament spool to sit on, specifically designed for the spool holder that comes with the Cetus 3D printer. For the 20*20 extrusion used as the spool holder for the Cetus...

The Tiertime Cetus 3D MKII printer has been verified to work seamlessly with this design, effectively distributing the forces across a wider area. ... Designed with precision using Fusion 360, this strain relief is engineered for maximum performance...

... The buzzer was a nuisance. I came across a cover design for the UP1 printers that might have worked on earlier Cetus models, but it definitely didn't fit my MK3. ...So, I put something together, and after a few iterations, I'm happy with the result.

The existing radial holders were all too cumbersome for me, obstructing the view of the object, so I designed a more compact version specifically for the Cetus3D MK2. ... I thoroughly tested the print using 0.15mm layer thickness, 100% infill, Fast...

... of the sliding mechanism's movement. For Cetus MK3 models, note that design differs significantly from its predecessor, MK2. ...Due to a mechanical limit switch incorporated into the system, the Z-axis rise is now restricted to just 2mm.

... remix for the heatsink is exceptionally well done. ... I own both the Prusa Mk3 and Mk2 and wanted the same setup for my Raspberry Pi 4 on my Mk2. ... This is remixed from the original Mk3 version as the Mk2 frame has different mounting hole locations.

A temporary z-probe holder for the Cetus 3D printer is being shared. Other printers with a similar extruder setup (Tiertime UP-series) may also work well. Inspiration comes from this Thing: https://www.thingiverse.com/thing:3462078 The holder's...

This is a replacement part for the weak printed belt connector on the z-axis of the Cetus 3D MKII printer. It can also be applied to the older MKI model. However, it needs to be printed from very tough filament. When printing, use PETG or Nylon. ... A...

This innovative design draws inspiration from Thingiverse's https://www.thingiverse.com/thing:3001088, but with a key difference - it securely attaches to the side of the extruder motor, addressing the issue faced by newer versions of the Cetus 3D...

I Decided to Create a More Versatile Cetus 3D Spool Holder That Can Accommodate Various Types of Spools. This New Design Makes Extrusion Easier Due to the Use of Bearings, Which Significantly Reduces Friction Caused by Spool Rotation. As a Result,...

Additional Hardware Required: Five to ten millimeter long M4 screws Tension coil springs (I sourced mine from a used laser printer cartridge) Three-millimeter VHB tape for secure adhesion How It Works: When you turn off the power on your Cetus 3D...

After upgrading to the new extruder for my Cetus, I realized that I had to mount my BL Touch / 3D Touch in a different way. So, I designed this new mount, which isn't extremely complicated to print. However, I highly recommend using ASA or ABS, as...

This is a front panel for the Cetus 3D printer. Update: The mount plate things are on the back of the mount plate, with some sunken holes that aren't perfectly sized and not deep enough. These holes are often referred to as captive nut caves. To...

The combined wall cabinet Cetus has reduced external dimensions without compromising the display volume. It has a low temperature base with either an upper cabinet with positive temperature (open) or low temperature (with doors). The considerable...

The combined wall cabinet Cetus has reduced external dimensions without compromising the display volume. It has a low temperature base with either an upper cabinet with positive temperature (open) or low temperature (with doors). The considerable...

Designed specifically to meet the needs of my trusty MK II printer, which I purchased back in December 2017 and have come to rely on ever since.

This is the fanduct for my buddy Alessandro's 3D printer, the Rotelloid - or as he calls it, the Shape3D. He's been raving about this thing nonstop. ...Anyway, it's also totally compatible with Prusa I3 MK2/MK3 printers.