cello 3d

Custom Molded Acrylic Shell Designed Specifically for Preamplifiers Associated with Cellists

In a few days it will be an entire necrodancer's ensemble.

Replacement backrest for my electric violin is desperately needed. This instrument, an affordable model manufactured in China, arrived with a curved backrest that poked me harshly in the chest (highlighted in blue) rather than lying flat like its...

El archivo stl no viene en el tamaño, hay que ampliarlo

Add-on to fit the Fishman Press 301 active pickup underneath the bridge of the O´Cello. This design also allows the built-in mic variant to fit. All cables must be stuffed underneath the lid, but there's plenty of space. ... Enjoy!

... snaps securely shut. A minor consideration: The person this device was designed for plays the cello in reverse of most other cellists. ...You might need to adjust the rod that goes into the bow frog to accommodate standard cello playing technique.

STL is one half of a reamer I used for enlarging holes to install geared pegs in cello. Firstly, wrap two printed halves in aluminum foil so they don't melt. Insert sand paper in between two halves then wrap around it them fully (cut at angle so it...

A modification to the O'Cello's alternative S-Curves that makes them work with the original's suggested 2x20x20mm L-bars. MAKE SURE to print the S-Curves such that the 'L' is 'upside-down' (similar to this: ┌), i.e. there is no unsupported...

Here's my version of ock10's design for fitting the 'Guitar EQ-7545R 4-Band EQ Equalizer System' onto my 2x20x20mm L-Bar version of the S-curve O'Cello mod (https://www.thingiverse.com/thing:6006065). Be sure to print with supports and make sure...

I wanted to replicate the electronics used in Petercb's O'Cello build and my own Mina electric violin project, but I didn't want to use any glue, as it makes plastic harder to reclaim into filament. I also wanted to keep all the electronics hidden...

Remixed from The O’Cello by cokane http://www.thingiverse.com/thing:1703629 and AddOns by Zarlor http://www.thingiverse.com/thing:1833270. I extensively reworked the knee rest pads created by ZARLOR, opting for 12mm carbon fiber tubing instead of...

Made in Venezuela

Minor adjustment to Part 6 provides a better fit for tuners. The original holes are oversized, and the wall is excessively thick, making proper tuner installation impossible (in my honest opinion). I purchased these tuners since the instructions...

There are two versions here. One is larger and rounded at both ends. One is flat on one end if you want an easier print and for it to sit flush with the instrument. I've tried 0.1 and 0.2 printing. ...and both work well.

This print came out messy but can easily be cleaned up. ...a few parts may break too but i just epoxy them back on.

"imperial_endpin_rect" is the piece that connects a 1/2" rod to another 1/2" rod at a 10 degree angle, so the endpin can be collapsed beyond the bridge of the O'Cello for storage. The caps are for the 1/2" aluminum tube. The fit is a little...

The preamp I used: https://www.amazon.com/dp/B01JUCJGTE/ref=cm_sw_r_cp_apa_fabc_PBEZW0D3D2WNT8BS00FG?_encoding=UTF8&psc=1&tag=thingiverse09-20 The piezo pickup included with the preamp works with the remixed o'cello bridge, but the heat shrink over...

This is o'cello with 1/2" center rod ( 13mm-ish hole ). First thanks cokane for the excellent model, I own a electric one but it is rather bulky, and I try to make a compact one in this build. I used these items: tube...

Here is o'cello with a 1/2 inch center rod (13mm-ish hole). First, thanks cokane for the excellent model - I own an electric one but it's rather bulky, so I tried making a compact one in this build. I used these items: tube...

Customized version of https://www.thingiverse.com/thing:713300 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=713300

The Case for the Revolutionary Aquos Sense Lite (SH-M05) Discover a New Era of Mobile Excellence Are you tired of mediocre smartphones that fail to deliver? Do you crave a device that truly understands your needs and exceeds your expectations? Look...

same thing just with a larger opening to cover the broken stud, superglue to the case, couldn't add this to the original design as it was throwing 404 errors when trying to edit it.

just 2 little blocks to place under the C and A strings at the very end of the finger board when you are checking the bridge height. ... photos to follow in time

Customized version of https://www.thingiverse.com/thing:713300 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=713300

This design is tailored to elevate a frame boasting a 19mm square section, ideally suited for a double bass stand, yet versatile enough to accommodate any item featuring a 19mm cross-section. ...Two distinct height options are included in the model.

Customized version of https://www.thingiverse.com/thing:713300 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=713300

Just in time for Halloween - a spider-themed cell end pin (rock) stop! Based on Drawn_To_Spec's "Black House Spider" (https://www.thingiverse.com/thing:3147004).Can be printed with spider already attached, or spider separate to make it easier to...