celestron nexstar 6se 3d models

Ducan Mask to collimate Celestron Nexstar 6SE

Bhatinov Filter for Celestron NexStar 6SE created using Bhatinov Mask Drawings Generator

I am using a Celestron Nexstar 6SE scope with the Hyperstar Mirror attached from Starizona, and connected to the Hyperstar is a ZWO ASI294MC PRO. I wanted the ability to cover the lens when I was done for the night without having to disconnect the...

Battery holder for the Celestron NexStar 6SE or 8SE tripod (perhaps also for other telescope brands / sizes?). The battery holder is designed for using 12V NiMH-Sticks. ...You can also fit in a 12V power outlet.

With this knob you don't need to remove the rubber grip. ... have fun!

This NexStar's hand control base was created to be able to use the 2x1 AUX port splitter connected to the celestron's HC connector because some accessories, like the StarSense camera and HC, will only work when connected to the HC plug in the NexStar...

This NexStar's hand control base was created to be able to use the 2x1 AUX port splitter connected to the celestron's HC connector because some accessories, like the StarSense camera and HC, will only work when connected to the HC plug in the NexStar...

this little thing helps you to get your objects right in the focus. it becomes especially helpful in astrophotography. just stick it over the focus-knob on your telescope and you can adjust your focus as you prefer. haven't tried it yet, should...

<p>This part seems to be easy to break especially if you carry it around without a protective hard case. I did it based on original measures but simplified compared to the original. So there is no weight reductive cutoffs etc. ...Made in SketchUp...

The AA batteries in the Celestron NexStar 6SE/8SE go-to telescope don't last very long, so I designed this holder to attach an external Mavic Pro drone battery for additional power. The rechargeable LiPo 3S Mavic Pro drone battery is rated 3830 mAh,...

Print in highest resolution and 100% infill. I cannot promise it will last, but it seems to be working fine for me. ... Remember to grease the gears.

Bahtinov Mask Celestron Nexstar 6SE

The Celestron NexStar 6SE and 8SE mounts are the same, except the gear cover/dovetail shroud. The 8SE shroud has a larger radius to accommodate the larger tube diameter. If you want to use a 6SE mount with an 8SE tube, you will need the larger...

I recently purchased an older Celestron NexStar 8 OTA and wanted to use the red dot finderscope from my Celestron NexStar 6SE. Unfortunately, the dovetail bracket for the finderscope doesn't align with the mounting holes on the NexStar 8. ... So, I...

This is an adapter to allow mounting a laser sight to a Celestron Nexstar 6SE telescope. When using a GoTo scope, you need to find the alignment stars during setup. In my initial use, I'm still uncertain about the utility of this as a finder. The...

Je l'ai conçu pour mon Celestron NexStar 6SE, Il est paramétrable pour le 8SE et beaucoup d'autres. À utiliser avant le pointeur qui a un champ de vision trop étroit : - Premièrement viser à travers le tube. - Deuxièmement affiner la vue le long...

This is a remix of the Celestron Red Dot Finder # 51630 Cover Version 2 by ssayer It doesn't fall off the red dot finder for my Celestron Nexstar 6SE I printed it with 0.6mm nozzle, 0.32mm layer height No need of supports

The Nexstar control is stored on the side of the telescope mount and I find this hard to get at when viewing. So I made this bracket. ...V2 adds a bracket to allow for mounting a SkySync GPS module preventing cord rap.

... paint acetone over the entire outside. It makes a nice glossy finish and really increases the strength. The dewshield has a flange that friction fits onto the 6SE. ... You can glue the extension onto this print to get a full 240mm dewshield.

Inserts for Celestron Nexstar telescopes. Big Hole to Camera or Other Big Hole to "Button" type GPS Small Hole to Eyepieces with the caps on! ... A tray for the stock diagonal

A motorized focuser for a Celestron NexStar SLT90, with a SCAD file that may allow adjustments for other telescopes. It houses a 28BYJ-48 stepper motor. The motor mount contains a long curved bar which can fit securely in the gap between the scope...

I remodeled this from a real hand controller using SolidEdge since no useful drawings are available from Celestron. The Accuracy is within some mm (most dimensions &lt; 1mm), Units are mm. ... Feel free to use it, let me know if you are also designing...

I recently got a Celestron Nexstar 6SE. If you have one of these, you know the built in AA batteries don't last very long. I purchased a rechargeable external battery from Amazon to use with the scope. This bracket allows holding the battery and has...

... fit in the base, and the original Starsense base holds everything in place. Accessories To fit the red dot finder that comes with the Celestron 6SE in the shoe you can download an adapter here You'll need a 3mm nut and bolt to secure the scope shoe

Any Skywatcher finder scope shoe will fit in the base, and the original Starsense base holds everything in place.AccessoriesTo fit the red dot finder that comes with the Celestron 6SE in the shoe you can download an adapter hereYou'll need a 3mm nut...

... everything in place. ### Accessories * To fit the red dot finder that comes with the Celestron 6SE in the shoe you can [download an adapter here](https://www.thingiverse.com/thing:321295) * You'll need a 3mm nut and bolt to secure the scope shoe

Remote holder for Celestron Nexstar Evolution telescope mount, a more convenient place for me than the tripod leg.

Customized version of https://www.thingiverse.com/thing:160391 for Celestron Nexstar 8se Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=160391

Motorized focuser fos Celestron Nexstar 130SLT Telescope. ... For assembly it's necessary: 1x 25GA motor reduced to 5 rpm 4x bearings 623-2RS M3 screws and nuts.

This is a tripod adapter for a Celestron Nexstar altaz goto telescope mount that I picked up used for cheap. ... This requires just two pieces of hardware, just a quarter inch screw to connect to the mount, and a 3/4" t-nut to allow it to screw to a...