celestron nexstar 127 slt vs 6se 3d models

This mask fits neatly inside a NexStar 6 Evolution and is easy to remove. ...Focusing works like a charm with an astro camera, takes out the guess work of lucky imaging.</p> <p>I've created the shape on this site: <a...

In order to fit the gear to the focusser on my telescope (nexstar 4SE 2017) I am able to gently pull the rubber focus knob off (just the rubber cover part, not the metal) and slide the 3d printed gear on (from the original design). This worked on my...

I recently acquired an older Celestron NexStar 8 OTA and decided to utilize the red dot finderscope from my Celestron NexStar 6SE. However, I encountered a problem as the dovetail bracket for the finderscope failed to align with the mounting holes on...

Bahtinov mask for Celestron Powerseeker 127 EQ

If you have a print size that fits, this works perfectly. It slides comfortably into the scope and then expands at the end so you can use the stock dust cover if you choose to leave the shield on, which I do. It's standard length (1-1/2x diameter).

Tray that rests on the rim of the mount and holds a Li-Ion battery or other accessory that you want to rotate along with the mount. Print without supports. ... Designed with Rhino 7

This adapter allows using the Celestron Nexstar SLT tripod as a regular 3/8 tripod. Thus, will allow to use it for any 3/8 mount (like the SVBONY SV225) or device (like the ZWO Seestar S50).There are two versions to the bottom part. With brass heat...

A replacement of the finder scope bracket for Celestron Powerseeker 127 EQ telescope finder scope.

Realistic 3d model of Telescope Celestron Nexstar 1025 LT

This replaces a broken dovetail mount for a red dot finder on a Celestron Nexstar 4SE.

I've created similar vibration dampening pads for my Celestron 127Mak, but the 6SE is heavier, so I designed a heavier duty pad for it - also considering the larger foot on the 6SE tripod. This design would work just as well for the 127Mak too. Part...

During printing you need to pause the print at the appropriate layer and drop in a M12-1.75 nut (if using Prusa Slicer, after slicing it, drag the layer slider to the layer just above the cavity and right click on the slider, and select "pause...

From what I can see by comparing it to Celestron's mount, it should also fit the 8SE telescope. To make it work on the 5SE, I would probably reduce its size so that it fits snugly against the smaller diameter of the 5-inch tube - however, since I...

Bahtinov mask to aid and improve focus on a 6" Celestron telescope.

Bahtinov mask to aid and improve focus on a 6" Celestron telescope.

Fine focus tool for Celestron's SCT, fits for Nexstar Evolution 9.25 and maybe other. ...Also work like dust cover cap for 1.25 prism.

This telescope is equipped with a lens plate and features a 90mm lens, following Newtonian design principles.

VERY IMPORTANT: the height of this custom tripod wedge could damage your telescope!\nI recently acquired a second-hand Celestron telescope, model Goto 127/1250. The seller didn't have the necessary bolts that connect the tripod wedge to the head; I...

This is a holder for Celestron Nexstar + Hand Controler that fits on AZ motorized mount that came with my AstroFi 150mm (6") Schmidt-Casegrain telescope. I had problems with the inbuilt GPS system in AstroFi, so i decided to buy the Nexstar+ hand...

Reduced the diameter of the original fine focus knob design to 50mm, ensuring clearance for the eyepiece/diagonal clamping ring and standard diagonal lock screws found on the Celestron NexStar Evolution 6. The previously customized 50mm version...

This adaptor plate allows to interface a Nexstar 6/8SE mount on a Celestron CG4 mount tripod. The list of needed hardware is described in the drawing. ... The purpose of the two M5 screws is to prevent the part to delaminate when torquing the M10...

This is a precision-crafted hand controller mount designed specifically for the Celestron NexStar, expertly paired with the robust CPC tripod featuring sturdy 2-inch legs. ...The revised design of the Tighter Fit model exhibits significantly less...

Introducing the updated myFocuserpro2 bracket for Celestron Nexstar 8SE, designed based on specifications by Vitaliy from Artyu Studio (https://www.turbosquid.com/Search/Artists/ARTYuSTUDIO). A huge thanks to Vitaliy for his assistance. The model is...

A remix of jamesdedij's "Holder for Celestron Nexstar Hand Controller" to suit a 40mm tube. I use this on my ARTCISE AS90C tripod. ... Could potentially fit a 1.5" tube too, particular if you scale it down to 99% but haven't tried.

This is a adapter fitting the tripod 2" eyepiece holes of a Celestron NexStar 4SE. With this it is possible to use the two 2" holes also for 1,25" eyepieces.</p><p>I highly recommend to print this with PETG as it is more flexible and durable. The...

This was designed to hold a TalentCell 11000mAH battery (model YB12011000-USB, purchased from Amazon) to power my Celestron Nexstar 8SE telescope. The TalentCell battery has a higher capacity than the Celestron PowerTank, is cheaper, and is far...

This was designed to hold a TalentCell 11000mAH battery (model YB12011000-USB, which I purchased from Amazon, https://www.amazon.com/gp/product/B016BJCRUO) to power my Celestron Nexstar 8SE telescope. The TalentCell battery has a higher capacity than...

Human: Bahtnikov Mask for Celestron Sky Prodigy 130 or NexStar 130. I generated optimal dimensions using http://astrojargon.net/maskgenerator.aspx and drew this design up in DesignSpark Mechanical. This mask should be suitable for any 650mm focal...

Remixed from Celestron Battery Holder, designed by tbergman8. Thanks for the original design. Modified to enable printing without supports as I encountered several issues with these on my flashforge finder. Cable management was also added for...

NexStar Evolution Tripod cap and leg holder clips for easy storage and transport. Safe vertical storage of tripod without damaging mount plate pin, surface or mounting screws, no wobble, no leg wandering around, and legs double as carry on handle...