celestron nexstar 127 slt vs 6se 3d models

Remote holder for Celestron Nexstar Evolution telescope mount, a more convenient place for me than the tripod leg.

You will need the following items for assembly of your Celestron Nexstar 130SLT Telescope: a 25-gauge motor, reduced to operate at five revolutions per minute; four 623-2RS bearings; and M3 screws along with their corresponding nuts.

I recently acquired a used Celestron Nexstar altaz goto telescope mount adapter for a fraction of its original price. ...This handy adapter can be quickly installed with just two essential components: a quarter-inch screw, which connects it securely to...

After the center piece of my Celestron NexStar 127SLT tripod cracked a few times I tried to look for a replacement piece. With no success, and after a few slight revisions, I came up with this bracket to help hold everything together. Hardware...

This custom-made brace is specifically designed to tackle the problem with the SLT mount that comes standard on many Celestron telescopes. The original single-sided fork, although robust in appearance, turns out to be a bit flimsy and only secured at...

This is a replacement foot for a Nexstar C11 fork mount tripod. It fits snug and I had to tap it in place with a hammer. I haven't used it much so I don't know how it will work in the long term. I would suggest that you print this foot on the side...

A perfect accessory for any telescope owner, this sturdy wall-mount securely fastens the Celestron telescope in place, keeping it neatly out of the way while allowing for easy access when needed. ...The included spacer cleverly attaches to the bottom of...

This is an adapter to fit on the Celestron 6SE (on the screws on the left side) to hold the SVBony SV165 Guide scope.

This spins the Celestron Nexstar 6 SE myFocuserPro2 version 3 for the Celestron Nexstar 8SE telescope. Measured by Wei Chen, who required this specific adaptation. Compared to the 6SE model, this version boasts reinforcement at the motor's rear.

I bought a Nextstar 127 SLT and the Celstron focus motor without first checking to see if they were compatible - which they are not. This adapter plate resolves the issue. You will need: 7x M3 Nuts 4x M3x20 OR M3x25 Bolts 3x M3x10 Bolts ...

Print in highest resolution and 100% infill. I cannot promise it will last, but it seems to be working fine for me. ... Remember to grease the gears.

I'm extremely frustrated with my Bahtinov Focus Mask, which I specifically designed for use with my Celestron SLT 5. ...To make the removal process easier, I cleverly attached a small piece of tape to one fin, but unfortunately, the pegs kept breaking...

This redesign was initially intended for use with a Celestron SLT tripod but should also be compatible with other tripods featuring 1.25" upper leg diameters and 7/8" lower leg diameters. In my specific case, the originals were secured with rivets...

Holder for Celestron Nexstar Hand Controller for C9 / C11 mounts ( or all 51 mm diameter tubes ). ... 40% infill 0.2 layer 4 perimeters

Pop-on knob for focus adjuster upgrade kit for Celestron Powerseeker 127 EQ telescope, ensuring precise tuning with ease. I've discovered that the standard Celestron knobs are often too tiny and frustrating to use, prompting me to create a...

Parts to cover gaps created by removing the metal part around the accessory tray on the Celestron Nexstar Evolution mount. ...It is useful to properly balance a 9.25 telescope without limitation in altitude.

Leg tightening bracket for Celestron NexStar tripod. Used pre-existing female nut insert from broken bracket and melted it into bracket using soldering iron. Used two half inch screws to secure bracket in place. ...Used ABS filament at 100% infill.

This microfocuser I designed specifically targets NexStar 6SE or 8SE telescopes, replacing their standard locking bracket entirely. In addition to the printed component, I utilized #10-24 threaded inserts accompanied by 1/2" screws and a 3/16" rod,...

Made from durable materials, this holder is specifically designed to accommodate the hand controllers for Celestron Nexstar C9/C11 mounts, as well as other telescopes with 51 mm diameter tubes. The case features a high infill percentage of 40%,...

The myFocuserPro2 is compatible with the Celestron NexStar 6 SE telescope, as evidenced by a 3D printed and functional bracket. The file formats include 3DM native (Rhino 3D), along with Step and Obj files for additional compatibility. An update on...

Crafted a custom leg tightening bracket for the Celestron NexStar tripod, drawing inspiration from a pre-existing female nut insert salvaged from a broken bracket. By skillfully applying heat from a soldering iron, I successfully melted the metal...

This is a printable Duncan Mask designed specifically for Celestron Nexstar SE8 telescopes. It's divided into four sections, carefully crafted to fit together seamlessly when printed. Once assembled, the mask provides essential protection during...

This is a mount and base conversion for an older Celestron Nexstar Mount. It was specifically designed for the Nexstar 80GTL, but would likely work with other models. One set of parts converts the clamshell clamp to a Vixen dovetail clamp; the other...

I have a Celestron NexStar 8SE telescope, so my girlfriend designed this for me, and I'm posting it here with her permission. Based on (http://www.thingiverse.com/thing:321295) Update: It works really well. If your printer is perfectly calibrated,...

Bracket that allows you to mount the Hand Controller on the Nexstar Evolution mount with facing to you.

So, I purchased a second-hand Celestron NexStar 4E - it's in pretty good condition, but lacks the spreader that firms up the tripod legs - so I decided to build one myself. My 3D Printer has a build area of 100 mm x 100 mm, so I had to design and...

This is a replacement for the rubber feet that attach to the bottom of the NexStar SE mounts. They are not exactly the same as the original but they fit perfectly and look great. ...Should be glued in place but they stay on to an extent without glue...

This is an adapter to attach a Vixenstyle dovetail clamp to the Nexstar GT mount. This means that other telescopes can also be used. The screw spacing for attaching the clamp is 35mm. ... You need 3x M5 nuts and 2x M6 nuts.

This mask slips perfectly into a NexStar 6 Evolution, making removal a breeze. Focusing with an astro camera is effortless, eliminating the uncertainty of lucky imaging. ...I designed the shape on http://astrojargon.net/maskgen.aspx, then uploaded the...

This is the mounting bracket which connects the legs on a Nexstar 4SE tripod to the top plate. It needs to be glued to the top of the tripod leg in place of the old bracket using epoxy or similar strong adhesive. ... I printed it using Impact PLA...