celestron cg5 3d models

PX14 to 2 LR44 adapter for a Celestron 8x50 Polarfinder - A crucial small flat-head screw requires precise placement using glue, as seen in the accompanying picture of a previous iteration. V2 has proven perfect: To further enhance user experience,...

Eliminate the blurry view while using Celestron SkyMaster binoculars by replacing the flexible plastic adapter with a more rigid one. Use a 1/4-20 nut and a 1/4-20x1" screw with a knob or wing-nut-style end for installation. Printable files are...

Using CATIA V5R21 software, I've created a model of the Celestron Nature DX binoculars for educational purposes. Please note that this is not an official model and certain details might be inaccurate. If you wish to render the model, feel free to do...

I initially created it to replace a damaged rail that securely mounted my 1x red dot scope on the Celestron 8-inch telescope. If your telescope's outer diameter significantly deviates from this standard, you will likely need to adjust the tubedia...

In addition to the datalogger, another product has been created - a device designed to enable the use of the Celestron Digital Microscope Imager 44421 with the Wesco VU 3000 stereo microscope, opening up new possibilities for microscale examination...

This is my take on a home brew Auratone 5C clone inspired by https://groupdiy.com/threads/auratone-diy.43086/ Given the original Maplin speaker is no longer available, I chose to use a Celestron 5” TF0510 speaker. ...This is available form a number of...

Lze připevnit k teleskopu Celestron Firstscope a dalším podobné velikosti. Telefon lze pomocí čepu seřídit tak, aby hledaný objekt byl uprostřed displeje. Po vytisknutí a sestavení je třeba slepit tělo s čepem (nezapomenout vložit matici :-) ). Tisk...

This is a whole new finderscope holder system for Celestron PowerSeeker 114EQ telescope. Original holder is terrible, so I created a new one, which is much more firm and also can carry both optical finderscope and laser pointer. Some M4 screws...

... used in its design - specifically Baader Astrosolar Safety Film - carefully selected for its exceptional performance. The telescope that inspired this project is the Celestron NexStar 114, boasting an impressive 130mm measured opening at the front.

A adaption of https://www.thingiverse.com/thing:160391 Bahtinov Mask Generator by https://www.thingiverse.com/brentb I removed the handle (which will break) and replaced it with a ring around the center and set the defaults for a Celestron Nexstar...

This is a holder for sun film for Celestron NexStar 130 SLT telescope. It is useful for astrophotography of the sun. You can find the sun image on my webpage: https://www.bajraszewski.pl/slonce. The holder comprises two parts: the holder...

I wanted to add a level to my Celestron Astromaster 130EQ telescope to assist in polar alignment. I believe this tripod is the CG-3, so any telescope that uses it should work. The levels I used are 9.5mm diameter x 31mm long cylindrical level...

Print Settings: Nozzle diameter - 0.4mm Print width - 0.4mm Layer height - 0.16mm Walls - 4 Print Speed - 50 mm/s I got the finderscope for a cheaper price from my local reseller, it is quarter the price of the original Vixen finderscope, it fits...

A very simple artificial star for collimating my Celestron 8. I use a thin coper plate with a very little hole, for this i use a needle to create a little dent ans use a very very smooth sand paper to sand the dent side. It's the same technique...

Adapter for tripod screw Celestron CPC Deluxe Mount - remove the snap ring and screw the original screw out - put the adapter over the screw and secure the cap with instand glue - screw it back in and put back the snap ring Adapter für die Schraube...

This is an innovative adapter designed for use with a 9x50 (Celestron or similar) finder scope to transform it into a guidescope capable of mounting a camera. The GuidescopeAdapter replaces the rear section of the finderscope, allowing you to...

This was modeled after the guidescope dovetail mount on my Celestron telescope. As far as I know, it is a standardized size. Internal width goes from 34mm to 24mm at an angle of 60 degrees (internal height 8.7mm). External width is 42.5mm. The...

... to the angle required for polar alignment. I suggest printing a DWARF II base strengthening item before tilting your DWARF II to prevent base breakage. I used an old Celestron 6x30 finder scope that came with my C8 telescope for sizing my print.

This design is based on the Celestron Red Dot finder, but after examining several others, I realized it's actually a generic model that can fit Orion's EZ-Finder II, Meade, and any other device with a similar look. ... Given all the feedback, I highly...

... and use M4 nuts. I used silk copper PLA matching the Celestron look. My 3D Printer is a Anycubic i3 Mega. Eventually you need to widen stuff, depending on your own printer tolerances. ...At least it gives you some insperations to make your own.

This project is tailored for Celestron's 76mm model, but it should work seamlessly with any affordable Chinese telescopes. To achieve precise gearing, the printing process demands a layer thickness of 0.2mm. ...For optimal results, I've included the...

Designed to mount my Cannon Rebel camera on my Celestron telescope. Telescope side dimensions based on a standard eye-piece with measured ID of 28.1mm, OD of 31.5mm, and slight recession for thumb-screws. On the camera side, small holes to engage the...

This redesign was specifically tailored for mounting the Celestron Starsense camera on my GSO RC 8inch CF telescope, but I had to drill out custom holes due to their imperfections. If further adjustments are necessary for this or other devices, I can...

Astronomy Red Dot Finder Holder for Large Binoculars 20x80 (25x100) or Similar Types Other Components: 7 x M3 Screws 5 x M3 Nuts 1 x [Red Dot...

Lens Cover for a Celestron Edge HD 8 with Hyperstar 4. Needed a cover that would work with the hyperstar installed. It is split in half so it can be put on without disconnecting cables. A revision is planned to add a small section to cover the...

Notably, it features a comprehensive e-mount interface that securely latches onto the camera body and boasts a sufficiently long tube, allowing the camera sensor to be precisely positioned at the focal length of the Celestron travel scope without...

This part serves as the foundation for mechanically combining two Celestron 70mm Travel Scopes into a pair of very comfortable astronomical binoculars. For assembly instructions, please visit petertinkerer.com. ... This part is specifically designed to...

Remix of wizalex's HEQ5 44mm Tripod Leg Holder to fit 50mm / 2" tripods like the Celestron CG-5 / AVX etc.Also removed excess material in the centre.V1: Original remix with hex-shaped hole.V2: Changed central hole to round to be better centred...

This is a focuser bracket for the Celestron Omni 150 XLT with focuser upgraded with the Lacerta 10:1 mecanism. This work also on Skywatcher Dobson 2 inches focuser. This is to be use with this thing project. Please refer to this project for...

To attach a Konus laser sight to your Celestron 6-inch telescope, first print and attach the sight according to the manufacturer's instructions. Next, adjust the sight as needed for optimal performance. This upgraded sight makes finding objects much...