celestron c8 equatorial wedge 3d models

This is a vintage Celestron equatorial mount replica, not meant for actual printing, yet its dimensions closely match those of the authentic product, making it an excellent reference model.

Equatorial adapter for my Celestron 4SE: still in development, but I'll share the files once I've finished testing it. The base plate won't fit on my printer, so I'm substituting it with an 18mm MDF cutout to resolve this issue. ... To assemble the...

Camera Adapter Mounts for Vintage Celestron C8 Telescopes - This ingenious adapter allows users to pair their old 1986 Celestron C8 telescope with a camera, making it easier than ever to capture stunning celestial images. The adapter features a...

This is a clip-on mask for a Celestron C8 telescope. It creates nice star spikes for astrophotography as if the secondary mirror would be held with arms like in a newton or RC telescope (or Hubble Space Telescope ;)). It is not made for visual...

A guiding block cable for Celestron C8

Secondary mirror supports for OTA Celestron C8 1983 Two repair parts.

this knob has been designed to enable easier and more accurate focus for vintage (orange) celestron C8 tubes. ... it requires a M3 screw longer than 15mm to secure it better to the original knob.

The Mask is designed for celestron C8 (and tested on a vintage one). ... I've created 3 versions: - 1 for the C8 with the secondary mirror holder of 66mm of diameter (tested on my vintage C8) (the files with 66) - 1 made starting from measures found on...

The Mask is designed for celestron C8 (and tested on a vintage one). I've created 3 versions: - 1 for the C8 with the secondary mirror holder of 66mm of diameter (tested on my vintage C8) (the files with 66) - 1 made starting from measures found on...

Picatinny rail for Celestron C8 mounts with ease. I attached this versatile accessory to secure an holographic red dot sight, but its uses go far beyond that. ...To assemble, print the two parts and securely fasten them together using M3 screws.

A base for a dew shield for Celestron C8 SCT. If printed in halves, it should be glued with CA or any other glue. Then wrap it with a piece of foam and glue it to form a dew shield. The base fits into the dust cap seat. ... Supports needed only for...

This is a dovetail mount for Celestron C8's. It might fit other 8" SCT's from Celestron as well, but I have no way of checking. The mount follows the curve of the scope so other sizes of SCT's like the 9.25 or 11 probably won't fit since the...

A segmented Dew Shield for the Celestron C8. Can be printed on smaller printers. You will need to print 4 segments and glue them together. A segment with a cutout for a Dovetail Bar is also included. ...You may or may not want to use it depending on...

This is a support to install a complete configuration ZWO ASI camera + canon 55/200mm teleobjective on the telescope Celestron C8. I use the existing support on the C8 with the existing 1/4" screw. Because I didn't find 1/4" screw to fix the...

This is an accessory mount for a Celestron C8 telescope that provides a standard 1/4 20 screw to attach a spotting scope. ...I designed it to mount my 3D printed 80mm f/4 refractor to my C8 telescope. It requires: one tripod screw - to attach...

The design is also available on Tinkercad so you can customize the screw hole sizes: https://www.tinkercad.com/things/4LjwJ2PkdNM-28-byj-48-celestron-c8-focuser WARNING: If using PLA, make sure to turn all the coils of the stepper motor to a low...

CELESTRON C8 XLT FOCUSER MOTORIZARION: All started when I found a couple of matched gears from a scrapped printer, that I though they could be used to motorize the focuser of my new C8 Celestron. As the bigger one was only 2mm thick, I decided to...

Actually designed with 3D printing in mind, this model has been utilized as a benchmark, derived from precise measurements of my own C8, though not necessarily to exact specifications, it still serves its intended purpose admirably.

This simple print enables you to convert your Celestron CG-3 equatorial mount to a 'traditional' 3/8 thread mount. You will need: 1 x 3/8-16 UNC 1.5" bolt 1 x 3/8-16 UNC nut 1 or more M10 x 40 washers (I used 2) Print 'Center 20220725' and...

Tri-Bahtinov mask for focusing and collimation. ...Fits standard Celestron C8 and Celestron Edge HD8.

A larger version of my static wedge to allow a Celestron Nexstar Mount to track in equatorial mode. This one fits mounts such as the Nexstar 114 GT, with a upper cone diameter of 125mm (the original one fits 100mm, and can be found here:...

A Static wedge to allow a Celestron Nexstar Mount to track in equatorial mode.This one fits mounts such as the Nexstar 80 GTL, with an upper cone diameter of 100mm (for an upper cone of 125mm, see https://www.thingiverse.com/thing:4879004). I've...

Solar filter adapter for Celestron C8, including front and back cover lids. ...The filter should be taped on underside of the insert piece.

Vixen / CG-5) to the Losmandy attachment points on a Celestron C8. This is useful when you wish to (1) attach your C8 to your mount using a Vixen bar, AND (2) attach a second vixen bar on the C8 for piggybacking a refractor or other attachment. The...

this is a dove tail support for vintage celestron C8, to enable easy and fast finder connection and exchange. a M4 bolt (both screw and nut) is needed as it fixes the finder. ... I suggest to print it in PETG or ABS (I use PLA only for home objects),...

A direct-bolt Vixen dovetail bar for a de-forked Celestron Celestar C8. It's broken into three pieces so that it can be printed on smaller beds. Use two threated rods to hold it together and give support. I have also included an adapter incase you...

This is the 3d model of the curved support to be used for attaching a Losmandy bar to a Celestron C8 or Nexstar Evolution 8. The curvature follows the tube perfectly and there is a drain in the middle so as not to force the clamping onto the...

These are customized "Smooth n' Curvy" knobs engineered specifically for securely attaching my Celestron 8" GPS telescope to its tripod. To assemble, use 3" long 3/8" bolts, which will leave a 1" protrusion from the knob. Depending on your printer's...

The system is mounted to the Celestron 0.63 reducer. Motor braket and telescope fixture can be printed in PETG I suggest the nema 17 coupler in TPU filament so that misalignment can be absorbed. ... I'm controlling the autofocusing process using...