celestron c8 avx 3d models

Leg Levelers for the Celestron Advanced VX Mount. This slips over existing foot, featuring a divot at bottom to center foot in tube. No modifications required and fully reversible. What to Print: 3 x Foot 3 x Thumbwheel 6 x Retainer Shim Designed...

Celestron AVX Rear Polar Cap

Original work: Front polar alignment cover/plug for a Celestron AVX

Fits a Celestron AVX tripod that has 2 inch diameter legs that are slanted 32.5 degrees from the vertical with accessory tray/spreader installed and tightened. 1/4" threaded insert on the shelf support is for securing the shelf. 6mm bolts in the...

This is a single large handle for the RA adjustment knobs of the Celestron AVX. ...Larger handles help reduce the force needed to turn them and give the added benefit of more fine control over the adjustment amount.

This is a bracket that will hold your hand controller for a Celestron AVX mount. This places it closer on the mount head. It slides into the hole in the mount head. ... An optional model will also hold a SkySync module

Two spacers for Celestron AVX mounts. First for spacing the counterweight shaft locking nut and the mount housing, the second for spacing a ADM dual saddle from the mount housing. ... May need only one, the other or both depending on your...

... up right. The Vixen is a bit too large for the Celestron. Now, I'm using the flashlight holder from my Vixen GP Mount with my Celestron AVX Mount. ...To make this work, I've separated it into two parts and used acetone to secure them together.

Celestron AVX - Intel NUC Adapter I make my designs available to the public under this license: "Attribution-NonCommercial-ShareAlike 4.0 International (CC BY-NC-SA 4.0)" https://creativecommons.org/licenses/by-nc-sa/4.0/ Disregarding these...

This is a custom knob designed for the Celestron AVX equatorial mount, which I crafted in Fusion360. My telescope mount came without one, making it impossible to attach the accessory tray, so I took matters into my own hands and created one from...

Simple cable holder that will attach to an AVX mount leg.

Camera Adapter Mounts for Vintage Celestron C8 Telescopes - This ingenious adapter allows users to pair their old 1986 Celestron C8 telescope with a camera, making it easier than ever to capture stunning celestial images. The adapter features a...

This is a clip-on mask for a Celestron C8 telescope. It creates nice star spikes for astrophotography as if the secondary mirror would be held with arms like in a newton or RC telescope (or Hubble Space Telescope ;)). It is not made for visual...

A guiding block cable for Celestron C8

Remixed. ...Made the center hole 20.5mm for a tight fit on Celestron AVX & CGEM mounts.

Secondary mirror supports for OTA Celestron C8 1983 Two repair parts.

To successfully attach a camera to a Celestron AVX mount, exercise extreme caution due to the brittle nature of the Kodak bolt in PLA. ...This material may not withstand the weight of a heavy camera.

AVX Leg mount for USB Hub

Fixed the center hole on the spacer at 20.5mm for a tight fit on Celestron AVX & CGEM mounts. Print Settings Printer brand: Prusa Printer: Mini Rafts: No Supports: build plate only Infill: 20 Filament brand: N/A Filament...

this knob has been designed to enable easier and more accurate focus for vintage (orange) celestron C8 tubes. ... it requires a M3 screw longer than 15mm to secure it better to the original knob.

The Mask is designed for celestron C8 (and tested on a vintage one). ... I've created 3 versions: - 1 for the C8 with the secondary mirror holder of 66mm of diameter (tested on my vintage C8) (the files with 66) - 1 made starting from measures found on...

The Mask is designed for celestron C8 (and tested on a vintage one). I've created 3 versions: - 1 for the C8 with the secondary mirror holder of 66mm of diameter (tested on my vintage C8) (the files with 66) - 1 made starting from measures found on...

Picatinny rail for Celestron C8 mounts with ease. I attached this versatile accessory to secure an holographic red dot sight, but its uses go far beyond that. ...To assemble, print the two parts and securely fasten them together using M3 screws.

A base for a dew shield for Celestron C8 SCT. If printed in halves, it should be glued with CA or any other glue. Then wrap it with a piece of foam and glue it to form a dew shield. The base fits into the dust cap seat. ... Supports needed only for...

This is a dovetail mount for Celestron C8's. It might fit other 8" SCT's from Celestron as well, but I have no way of checking. The mount follows the curve of the scope so other sizes of SCT's like the 9.25 or 11 probably won't fit since the...

A segmented Dew Shield for the Celestron C8. Can be printed on smaller printers. You will need to print 4 segments and glue them together. A segment with a cutout for a Dovetail Bar is also included. ...You may or may not want to use it depending on...

This is a support to install a complete configuration ZWO ASI camera + canon 55/200mm teleobjective on the telescope Celestron C8. I use the existing support on the C8 with the existing 1/4" screw. Because I didn't find 1/4" screw to fix the...

If you don't have the room on your OTA to mount a guide scope for some reason, and have a newer AVX with the dual saddle, this allows you to have a dovetail mount or blank plate on the unused side of your AVX mount. Added a larger double version for...

This is an accessory mount for a Celestron C8 telescope that provides a standard 1/4 20 screw to attach a spotting scope. ...I designed it to mount my 3D printed 80mm f/4 refractor to my C8 telescope. It requires: one tripod screw - to attach...

The design is also available on Tinkercad so you can customize the screw hole sizes: https://www.tinkercad.com/things/4LjwJ2PkdNM-28-byj-48-celestron-c8-focuser WARNING: If using PLA, make sure to turn all the coils of the stepper motor to a low...