celestron c5 sct visual back 3d models

A revision of the M3 Thumbscrew to allow for a press-on knob to overcome the torque limitations of the teeny-tiny heads on the stock Celestron 1.25" SCT visual back.

Slip this knob over the rubber focuser on your Celestron C5 SCT The 40mm diameter of this fine focuser knob allows greater precision with manual focusing.

Basic Tube Rings for the Celestron C5. Please note that the rings are slightly oversized. This is so there is room to glue a layer of foam 2-3mm thick to bettter grip the tube and avoid scratching. ... Use 1/4' bolts to assemble it.

A basic dew sheild for the Celestron C5.I have made two versions, one is just a normal tube, the other has vanes the will produce diffraction spikes on bright stars. The sheild is slightly oversized because it's intended to have a 1-2mm layer of foam...

A set of basic tube rings for the Celestron C5 that allow for mounting to a Vixen-Type Dovetail Bar.The Tube Rings have an internal diameter of 150mm. They should fit any instrument with that same diameter casing (not to be confused with objective...

Visual back with 2" diameter, useful to test your eyepieces or camera. Should be sturdy enough for a continuos use (in case you don't want to buy a metal one). Also, should work with bigger SCT scope, I tested it only on my C5. The lateral holes...

I purchased C8 telescope without Visual back, and had problem founding one due to the pandemic.Also there is no such thing on Thingiverse, and I used to found everything here :) Anyway I used few things from thingiverse as base of my thing and...

Original work: Cable management for the top back of an SCT scope.

The Celestron 1.25 visual back slides all the way onto this and locks down. bump the threaded face of the visual back up against the seated flange. from camera mojunt plane, to the end of the 1.25 inch tube is 60mm. 60mm + the canon's native 45mm of...

# USE A 2040 rail with printed parts to mount your telescope accessories and save $100s This project enables you to use a standard 2040 aluminium extrusion on top of a Celestron 9.25" and 8" SCT optical tube, as a way to mount accessories. The...

The outer diameter is 140.3mm and leaves a bit of room because the the C5 tube is not exactly centered around the inner collimation part (the 45.7mm part in the middle). See...

This is a support for a step motor (28BYJ-48) to focus on Celestron C5 scope. It comes in 4 parts: - The support - The motor case - The gear - The shaft cap You need some M3 bolts with nuts. 2 M3 (8mm) bolts with nuts in the gear. You put...

This is a Bhatinov Mask for a Celestron 8in SCT. ...I designed the using the [Bahtinov Mask Drawings Generator](https://satakagi.github.io/tribahtinovWebApps/Bahtinov.html).

Slip this knob over the rubber focuser on your Celestron SCT. It fits mine as-is, but can be customized to fit a different size. ...The 70mm diameter of this fine focuser knob allows greater precision with manual focusing.

Base for Telrad view finder. ...I designed this to fit a Celestron 8in SCT OTA with an outer diameter of 238 mm. ...If you want a base for a different diameter OTA, message me with the diameter you want and I can modify the model.

Mounting plate for Celestron SCT 9.25" (11") finder dovetail ###BOM 2x M4x20mm screw 2x M4 nuts ### Optional * Aluminum Alloy Quick Release Plate Clamp for Tripod Monopod for Arca Swiss or * Vixen style telescope clamp ###Note Use a M4 tap to create...

... 1 1/2 inches apart but I have not tested. I don't use the finder scope that much as I have a Celestron Starsense camera, but I occasionally like to check my alignment with it. I included the STEP file if anyone wants to modify it. ...Feel free.

The system is mounted to the Celestron 0.63 reducer. Motor braket and telescope fixture can be printed in PETG I suggest the nema 17 coupler in TPU filament so that misalignment can be absorbed. ... I'm controlling the autofocusing process using...

Customized version of https://www.thingiverse.com/thing:4581618 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4581618

--------------------------------------------------------------------------------------------------------------------------- Español: ======= Mordaza Vixen compatible con la curvatura y tornillos que monta el Celestron C6 y C5, con 2 agujeros para...

Bahtinov Focus Mask for Celestron SLT 5 I added a small bit of tape to one fin to make it easy to remove....Pegs just break off!!

There should be a bit of clearance between the bottom of the adapter and the back of the SCT tube. You can then mount the focus motor onto the adapter using the captive screws on the motor. I threaded the screws from the motor straight into the...

C5 Corvette seat back release bezel. These are getting harder to find and most have developed cracks. Modeled this up to try and these are first prototype files. ... Have also uploaded the Fusion and Step Files.

I was looking for Bahtinov mask for my 9.25" SCT but unfortunately most of the files i found was not compatible to my small 3D printer. i decided to design my own mask which i can assemble later using groove. THIS PRINT NEED GLUE TO ASSEMBLE* ...

I didn't want to attach my ZWO EAF to my C9.25 permanently, as this makes it harder to transport and cumbersome to use visually. I designed the holder in a way that only a small base part is attached permanently and does not hinder using the...

Customized version of https://www.thingiverse.com/thing:160391 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=160391

Customized version of https://www.thingiverse.com/thing:160391 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=160391

Celestron C5 Bahtinov mask for use with dual F6.3 reducers. ...Brings the FL at 500mm F/4.

Customized version of https://www.thingiverse.com/thing:2011552 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2011552

Customized version of https://www.thingiverse.com/thing:2003119 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2003119