celestron avx polar scope 3d models

This is for high power laser pointer with a diameter that just barely fit in the polar scope tunnel, I'm sure you can remix it for smaller scope but as is the tolerance is so tight that even 1 layer of electrical tape won't fit. ... Polar scope thread...

Celestron AVX Rear Polar Cap

Original work: Front polar alignment cover/plug for a Celestron AVX

... But this doesn't fit into the Celestron Advanced VX Mount. The Vixen is a little bit to big for Celestron. Now i use the flashlight from Vixen GP Mount also for the Celestron AVX Mount. This are two parts. ...I use acetone to adhere it together.

Celestron Item #: 94224 https://www.celestron.com/products/cg-5-avx-cgem-polar-finderscope 3 3/8" 16 tpi nuts. https://www.homedepot.com/p/Hillman-Stainless-Hex-Nut-3-8-16-2532/204786068 This item uses PLA and TPU. End Caps and Lock are made...

... setup is not easy using this finder. Adding the lighting module of an illuminated eyepiece, this support enables to illuminate the polar finder 's reticule. Note: using black filament is not a good idea: prefer light color filament ! ...

Leg levelers for the Celestron Advanced VX (AVX) mount. This slips over the existing foot and has a divot in the bottom to center the foot in the tube. No modifications required and 100% reversible. What to print: 3 x foot 3 x thumbwheel 6 x...

Fits a Celestron AVX tripod that has 2 inch diameter legs that are slanted 32.5 degrees from the vertical with accessory tray/spreader installed and tightened. 1/4" threaded insert on the shelf support is for securing the shelf. 6mm bolts in the...

This is a single large handle for the RA adjustment knobs of the Celestron AVX. ...Larger handles help reduce the force needed to turn them and give the added benefit of more fine control over the adjustment amount.

This is a bracket that will hold your hand controller for a Celestron AVX mount. This places it closer on the mount head. It slides into the hole in the mount head. ... An optional model will also hold a SkySync module

Two spacers for Celestron AVX mounts. First for spacing the counterweight shaft locking nut and the mount housing, the second for spacing a ADM dual saddle from the mount housing. ... May need only one, the other or both depending on your...

This is a knob for the Celestron AVX equatorial mount, which I created in Fusion360. My telescope mount arrived without one, so I couldn't attach the accessory tray, so I modeled one myself. This requires a standard M12x1.75 nut (I used a Grade 8...

Celestron AVX - Intel NUC Adapter I make my designs available to the public under this license: "Attribution-NonCommercial-ShareAlike 4.0 International (CC BY-NC-SA 4.0)" https://creativecommons.org/licenses/by-nc-sa/4.0/ Disregarding these...

Remixed. ...Made the center hole 20.5mm for a tight fit on Celestron AVX & CGEM mounts.

To fix a camera on a Celestron AVX mount. !!! ...Be careful: Kodak bolt in PLA is very fragile for heavy camera !!!

If you don't have the room on your OTA to mount a guide scope for some reason, and have a newer AVX with the dual saddle, this allows you to have a dovetail mount or blank plate on the unused side of your AVX mount. Added a larger double version for...

AVX Leg mount for USB Hub

Fixed the center hole on the spacer at 20.5mm for a tight fit on Celestron AVX & CGEM mounts. Print Settings Printer brand: Prusa Printer: Mini Rafts: No Supports: build plate only Infill: 20 Filament brand: N/A Filament...

... to hold an Olympic weight plate. Much cheaper than the Celestron weights. Use a 1/4-20 tap for the side hole. I used a small piece of rubber in the hole and a thumb screw to push it through. ...You need something rubbery to make it grip the bar.

Celestron Polar Finder AVX/Cgem hot shoe mod to fit on top of a Vixen Polarie.

Side mount for polar scope for CG-3 Celestron EQ mount,requires 2x M4 bolts and nuts to connect

This adapter will turn your cheap finder scope into polar alignment scope for Celestron CG-5 mount. I used 10$ Seben 5x24 [http://tiny.cc/7ofaly] finder scope purchased from ebay for this project. Remark: I made a 1,5 cm shorter print of this...

A replacement dust cap for the polar scope on the EQ6 / NEQ6 telescope mount. ... May also fit the EQ6

It is designed to match the threads on the tube that accepts the standard Celestron polar axis finder scope (m28x1). I have sized the internal hole to provide a very tight fit for my laser pointer (23.5 mm diameter). Print slowly to prevent...

Print Settings: Nozzle diameter - 0.4mm Print width - 0.4mm Layer height - 0.16mm Walls - 4 Print Speed - 50 mm/s I got the finderscope for a cheaper price from my local reseller, it is quarter the price of the original Vixen finderscope, it fits...

There was not enough space in the original housing for a belt drive modification. Also is enough space in the dec housing for noise insulation. ... You need 7 m3 thread inserts for the beld drive you need 4x Drive Belt Pulley T2,5 28 Teeth, 6mm...

This is a remix which I made which I feel better fits the mount. ... I also enlarged the nut holes to fit standard sizes I found at the local hardware store.

Customized version of https://www.thingiverse.com/thing:3197218 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3197218

I modified the Scad model of thing:3062413 and made a bubble level indicator use round spirit level. Hole diameter is 10 mm. ...You can use double sided adhesive tape for fixing it to the mount.

This is a shim I created to reduce or remove the slop between the polar scope and metal bracket. This helps a great deal when aligning to Polaris for deep sky photography and provides a much tighter fit for greater accuracy. The shim should be used...