celestron 127eq 3d models
1002 3d models found related to celestron 127eq.thingiverse
Laser holder for a Celestron 127EQ. Mounts to the existing finder scope screw studs using the existing thumb screws. Designed to sit on top my finder scope holder. It may work with the factory finder scope holder. ...It is not designed to work...
youmagine
This is a 3d model of a cap used to aid in collimation of the Celestron 127EQ newtonian reflector telecope. This was described by niuno15 in this...
thingiverse
This is a replacement finder scope mount for the Celestron 127EQ telescope. It mounts to the two factory screw posts with the original thumb screws. The finder scope is positioned further away from the telescope than the original since I thought...
thingiverse
This is the faster way to find the center on primary mirror on your Celestron Powerseeker 127EQ, in this mode you can mark the center for easy collimation. ...
thingiverse
Printed with the top down with support so the holes come out correctly. ...Only hardware needed is a 1/4-20 bolt to thread into your camera body and bolts to mount to the equatorial mount Good if using a drive motor with the mount and want to do wide...
thingiverse
Quick dirty picatinny style mount for celestron 127EQ telescope. I wanted to put a red dot on in place of the normal finder scope. This may need some modification for other telescopes. ...There are much better options out there, this was just something...
thingiverse
Tri-Bahtinov mask for the PowerSeeker 127EQ telescope.
thingiverse
Customized version of https://www.thingiverse.com/thing:266400 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=266400
thingiverse
This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/7z7iulL8ym9
thingiverse
It is designed for the 20 mm eyepiece from Celestron, the body of the eyepiece has an angled mounting section. I printed this eyepiece side down, telescope side up with supports. ( EGADS! I just saw a typo on the part as I uploaded the...
thingiverse
The Celestron Regal M2 spotting scopes have an adjustable eye relief ring that rotates to change eye relief distance. Clamping to this ring means the phone camera will swing around and not stay aligned. Removing this ring is easy (it unscrews) but...
prusaprinters
Celestron Leg Stabilisers Case - Holds 3x Leg Stabilisers
thingiverse
Clip to keep Celestron tripod legs togather, in various manners. ...
cgtrader
Detailed model of Celestron Telescope Rendered with C4D. ...Polygonal Polygons 21317 Vertices 21693
pinshape
this is an ABS replacement arm for the celestron telescope tripod spreader
thingiverse
Replacement arm for the tripod on the Celestron 130 Series of Telescopes - may fit other models.
thingiverse
Extended Lock lever for the Celestron CG4 or Skywatcher EQ 3-2 mount.
thingiverse
A Celestron C80ED Bahtinov Mask which fits over the screw on telescope dewshield. ...
grabcad
The Celestron CG5-GT equatorial mount features a tripod for support and stability during astronomical observations.
thingiverse
This is a part acessory for a Celestron Powerseeker 70az Telescope Tripod. I have printed it in 20% infill with supports. Print 3 supports for each base. ...
prusaprinters
A front lens cover for Celestron Binoculars. ...We designed and printed this out of TPU and it has fit snuggly and worked great!
prusaprinters
The inner lid (6.5cm diameter) for a Celestron 114LCM telescope lens cap.It's a bit rough but it works.
thingiverse
This is a remix of the Celestron Red Dot Finder # 51630 Cover Version 2 by ssayer It doesn't fall off the red dot finder for my Celestron Nexstar 6SE I printed it with 0.6mm nozzle, 0.32mm layer height No need of supports
thingiverse
This is a replacement handle for a Celestron 11lb counterweight handle. This will have a tight interference fit on the top of the screw. ...Use a vise to slowly press it on.
thingiverse
Just a case for a Reducer- Corrector. ...It came with a silica gel packet so I made a lid that can hold it too. https://www.celestron.com/products/reducer-corrector
thingiverse
This is a front lens cap for a 1990's Celestron C90 telescope. This model will only fit the black tube C90 scopes. ...I will develop another variation for the older orange tube C90 scopes.
thingiverse
Realicé este sencillo modelo para usar mi "Celestron 51630 Star Pointer Telescope " la parte anterior se rompió y no podía fijarla correctamente. ... El modelo es un poco más grande que el original pero cumple su función con exactitud.