cd drive bay 3d models

This is a CD/DVD/Bluray desktop 5-1/4 drive cabinet / case to be printed in 2 parts and assembled with a few screws and nutsMaterial4 M3 Square nuts4 M3 6mm Allen bolts4 M3 25mm Allen bolts 4 rubber / cloth pads (optional)For more information...

This is a caddy to mount an HDD in replace of a CD Rom drive. You are able to reuse the bolts from the HDD to mount the caddy and also comes with clips to hold the HDD in place. ...These clips are optional as the HDD sits quite snuggly.

Replica of the authentic drive bay cover designed specifically for the Corsair Carbide 300R PC enclosure.

Compact Storage Drawer Optimized for 5.25 Inch Optical Drive Bays - Fully Customizable

When you require a paper clip to open your CD/DVD drive tray, simply print this design at 50% infill and 0 shells, with a size of 30mm. Ensure the wire is thick for easy insertion without glue. The hole is perfectly sized for a straight paperclip...

5.25" drive bay cover for Bitfenix Prodigy ITX case. ... Usable with fan screw holes on print.

This is a direct replacement for the drive bay door hinge on your Corsair Obsidian 800D case.

My G20AJ was overeating after I installed a SSD, so I made this modification to blow air inside the computer (SSD is near the old CD-Drive), so as to cool it down.The fan used is 40x10 centrifugal fan slotted in without any screw, there is a cut for...

It follows the exact CD drive standards so it should fit seamlessly into any computer case with drive bays. The only tested case so far has been an Antec 900. Print Settings Printer Brand: RepRap ...

Add-ons: [linear drive conversion](https://www.thingiverse.com/thing:3107269) The materials you'll need include: 1 motor from a CD drive or similar device 1 adapter for the power supply (3-12V works well) something to secure the gears in place, such...

Apple's Macintosh PowerBook 1400 has a common failure these days -- the thin brackets that hold the front bezel to the CD-ROM drive module tend to crack and break. Since the machine is from 1996, brittle plastics are to be expected, so these new...

There's also room for CD/DVD media, such as system recovery discs, or you could even put in a USB hard drive - I used my Western Digital Passport with the cable. I created another one that's blank without the SD card slot, for those who don't need...

This caddy converts a 2.5" HDD to fit the 9.5 slim DVD drive bay. However, you'll also need the connection electronics to make it work. If you have the 12mm HDD adapter, you might be able to reuse its circuit board. ...To secure the HDD and board in...

This is for 2.5" HDD caddy to the 9.5 slim DVD drive bay. Unfortunately you'll need the connection electronics as well. If you are having the 12mm HDD adapter that can donate the circuit board. ...The HDD & board can be secured with wide tape as in...

Featuring dual Z and Y motors, and a heated bed. Features:Dual motors on Z and Y for improved reliabilitylinear bearings on all axisIntegrated extruder and spool holderDuet3D board and LCD.Parts required 5x CD Drive stepper motors. This gets tricky...

5.25" Drive bay for hackintosh computer. ... All units are in imperial so if your system is metric scale to 25.4"/mm or 2540%

U.2 Drive Bay for server, I did mine in PLA CF, I used a 3000 rpm Noctua fan to get acquitted air flow.

This adapter attaches to the face of the enclosure, so bays are available for installing hard drives and other componentscustomized for my home server case

Cover for a 5.25" optical drive bay. Uses the screw holes from an actual drive. It can be used with ANY computer case. ...Most computer case makers include proprietary covers. Drill the holes to about 2.8mm and make thread screwing in a standard optical...

Cover for a 5.25" optical drive bay. Uses the screw holes from an actual drive. It can be used with ANY computer case. Most computer case makers include proprietary covers. ... Drill the holes to about 2.8mm and make thread screwing in a standard...

... Pro. Not all cases use the same hook-length for their Drive-Bay covers. Measure the hook positions of the drive-bay covers that came with your case, and then use the Fusion360 file in the link below to modify the file for your specific case.

This CD mount for the Spotify Car Thing raises the device up and to the left, to avoid the car's radio LCD.Assembly Instructions&nbsp;Unscrew the adapter disk from the CD Mount with a Torx bit. ...Be careful not to lose this screw.</li><li>Place adapter...

This is a user-friendly cover plate, which easily fits into your computer's front panel as a replacement for the current drive bay covers. It features cutouts for mounting fans in the vacant drive spaces. ...Suitable for securing TWO 2.5" optical...

5.25" Drive bay for hackintosh computer. All units are in imperial so if your system is metric scale to 25.4"/mm or 2540% Category: Electronics

Headset Holder Mounts for 5.25 Drive Bay. Fits perfectly in Cooler Master Storm Scout Chassis. Remix based on original design from thingiverse.com. ...Increased hook width for better headset support.

A compact adapter solution designed specifically for an Arduino Uno board, allowing seamless integration into a standard 3.5-inch drive bay of your desktop computer to power and control vibrant RGB LED lighting.

I remixed the 5.25 drive bay cover switch panel specifically for my Fractal Design Define R4. ... The recommended settings include a moderate infill percentage of 12-15% and three perimeter layers to achieve optimal results.

Have had the best luck printing in ABS, PETG failed after one summer in the carAssembly instructions form original model apply here as wellAssembly Instructions Unscrew the adapter disk from the CD Mount with a Torx bit. ...Be careful not to lose this...

... print time for one set of two HDD rails is roughly 1.5 hours when printing at a layer height of 0.2mm. Note: I haven't printed the CD/DVD rail myself, as it was modified from an existing HDD rail design and should be generally okay to use.

A vertically oriented dual 5.25 inch drive for the Corsair P3 computer case.Print SettingsPrint with the bottom side on the build plate (for orientation see P3 Dual Drive Bay.3mf).Needs lots of supports