catan game piece holder 3d models

Print your own robber for a 3D-printed Catan set by using andreas's Hitman figure, scaled down and placed on a base. However, be aware that this process generates a large STL file. Despite the spindly limbs and requirement for support, you can still...

Various Case pieces to hold 3D printed Settlers board game pieces. This design works with other cases found on Thingiverse here: https://www.thingiverse.com/thing:1749597. This design makes it easy to quickly put away your Settler gaming sessions.

http://www.thingiverse.com/apps/customizer/run?thing\_id=434793 Instructions Using the following options: card_length = 81 overhang = 16 holder_count = 6 top_offset = 14 clip_card_gap = 0.25 card_width = 64 card_gap = 5 support_gap = 0.25...

A card holder that can be combined with another card holder

A card holder for two sets of cards (base settlers, and cities and knights). These fit the larger cards that are standard these days - 2 1/8" x 3 1/8" cards. I'd print the support for the cover to get the holes nice and round, and the base should...

Here are the parts I've created for use with JAWong's 3D Catan Pieces (http://www.thingiverse.com/thing:26979). The pieces are designed with intricate details, so you may need to print them at a moderate pace. When designing these parts, I focused on...

I didn't like all the other Hex Holders do i create my own Have fun

... a tile stacker for https://www.thingiverse.com/thing:380793 tiles. ...You'll need one for the tile holder stack, one should work for the flat sea tiles as well. You may need two for the textured sea tiles. ...I'm not sure as i haven't printed it yet.

... build this assembly, you will need 1 'spine', 3 'feet', 4 'ribs', 4 'edge fingers' and 4 'center fingers'. ...the pin system is very intuitive to figure out, but the tolerances are not good enough to hold the pieces together without glue in my opinion.

Card Organizer System for Efficient Storage Custom Design Made Possible through Advanced Customizer Technology at Thingiverse Website Project ID: 434793 Access and Configure Options using Integrated Interface Setup and Assembly Instructions: Choose...

... I want a little bit of a more fancy holder with labeled lids. I used these number tokens. The threads should have been a little less fine, but the still work great be patient. Please give a like if the file is good. tips are always welcome.

Original was weirdly small, not tall enough to hold all number tokens for the game board. Remixed ensuring height and diameter of tokens will fit inside. ... Also made the lid taller to compensate, but also internal lid diameter smaller by 0.5mm to...

Remixed to make the hole sizes larger, as mine didn't fit in several ways. ...Road pieces now 5.7x5.7mm Town pieces now 15mm wide Castle pieces now 42mm long Category: Toys & Games

Remixed to make the hole sizes larger, as mine didn't fit in several ways. ... Road pieces now 5.7x5.7mm Town pieces now 15mm wide Castle pieces now 42mm long

Sturdy Card Container for Organizing Sleeved Catan Decks A robust holder designed to accommodate thick sleeves and securely store the additional cards required for 5-6 player games of Settlers of Catan.

This item is well-suited and allows some room for irregular components.

Holds my Shogi game pieces. ... Holder has dividers to keep pieces separated by rank

If you desire players and awards similar but not GoT themed, click on this link: https://www.etsy.com/listing/540085532/catan-base-set-accessories-awards?ref=listing-shop-header-1 ------------ These Game of Thrones themed files serve as accessories,...

The base Catan game and Seafarers expansion can be comfortably held in SCAD. To accommodate other expansions, edit SCAD as needed to deepen certain places. For easier printing, divide the design into four distinct pieces. Printing this model on a...

Storage for Settlers of Catan Game 2 parts: base + cover Need 4 non polar magnets 4mm diameter (4x2) or 2 magnets and 2 balls for air pistols ))

BOARD GAME PIECE

Replacement Trouble Game Piece

... ... I did a remix by combing Catan Magnetic roads by Oldman_Winter and Catan game Water / Border remix by Jaktech https://www.thingiverse.com/thing:5806895 https://www.thingiverse.com/thing:4746625 Need to print and wait for my magnets to arrive.

This is a 2-4 player card game adaptation of the board game edition, initially named "The Settlers of Catan." It was processed through Agisoft Metashape Professional software. Invented by German designer Klaus Teuber in the mid-1990s, the original...

This is a nice card holder when playing Rivals of Catan to keep the whole game process organised! Print instructionsI printed in Black PLA, .20 Layer height, No supports or anything. ...Very easy print.</p>

Replacement game piece for the Trouble Game

Game piece tray(s) for Gloomhaven or other games that contain a lot of pieces.

It can be stored in the insert designed to store Catan + Expansion in the original game box: [Catan Insert + Expansion 5-6 Player (European Edition)](https://www.thingiverse.com/thing:4902693) ** Printing Instructions **...

I've owned a Catan Card Game for years - and the original insert was made of cardboard, making handling somewhat cumbersome. So I designed a new simple insert that also accommodates space for at least two expansion sets. I divided the insert to fit...

I've owned a Catan Card Game for years - and the original insert was made from cardboard which made handling somewhat cumbersome. So I designed a new simple insert that also provides space for at least two expansion sets. I divided the insert...