catalyst machineworks massive droner 3d models
24749 3d models found related to catalyst machineworks massive droner.thingiverse
Replaces the tpu part for the catalyst machineworks massive droner 3 inch hd. Mounts an immersionrc ghost qtee antenna and a vista antenna. ... full build: https://rotorbuilds.com/build/26782
thingiverse
I didn't like the stock mount with the Massive Droner HD and the angle it put the antenna at so I created this.
thingiverse
I'm mounting the SQ12 camera on the Catalyst MachineWorks Massive Droner today. I've expanded the SQ12 casing by a fraction of a millimeter to ensure a snug fit. With some help from a heat gun, it now slides onto the Droner with ease. I haven't...
thingiverse
TPU Mounts to utilize the Sharkbyte TX5M.1 on the Catalyst Machineworks Massive Droner HD with the minimortal antenna. I used a Foxeer Lollipop antenna but since the antenna support is designed to have the cable tied to it any MMCX should work. ...
thingiverse
Fin for the Catalyst Machineworks Raging Droner. The 6.0mm Fin is specifically designed to assist in achieving turtle mode. A spacer is utilized to center the front portion of the fin. When combined with my Antenna Block, it provides a superior...
thingiverse
The Catalyst Machineworks Raging Droner requires an integrated capacitor holder, available in two options: one that accommodates the TBS Crossfire antenna and another that does not.
thingiverse
This is an upgraded antenna block designed to work seamlessly with Catalyst Machineworks Raging Droner. As a replacement for the standard antenna block, this custom design fits perfectly with both the stock 3D printed accessories and my Fin design.
cults3d
It is a Re-design of the Rayenator "Catalyst Machineworks Arm Guard" https://www.thingiverse.com/thing:3688251 Add extra protection Now I can hit concrete without delaminating the arm. Original design was good but I need more protection. Add...
thingiverse
Here is a re-design of the Rayenator "Catalyst Machineworks Arm Guard". I've added extra protection, so now I can hit concrete without the arm delaminating. The original design was good, but I needed more protection. To secure it, I've added...
thingiverse
The Catalyst Machineworks Raging Droner was designed to meet the needs of demanding pilots. To prevent unnecessary stress on the ESC-to-Battery pigtail, this component was introduced as a standard feature. In the event of an unexpected battery...
cults3d
I made it to be able to fly until I receive replacement part from Catalyst Machineworks. I print it with PETG. I still fly with it. ... It stills survive to many hard crash
thingiverse
I manage to keep flying until a replacement part arrives from Catalyst Machineworks. I manufacture the new part using PETG, which holds up remarkably well under stress. ...Despite taking several rough landings, my machine continues to function...
cults3d
A simple Print . ... It allow you to install RaceLite LEDs or Racewire on the thin arms of the Raging Droner.
thingiverse
The user-friendly Print allows for effortless installation of RaceLite LEDs or Racewire onto the slender arms of the Raging Droner.
thingiverse
This Profile is Heavily Based on Calefpv's "Raging Droner RD5 Rear LED Sma" (https://www.thingiverse.com/thing:3688516), Which Was a Great Starting Point. ... I've Made Some Key Additions, Including: A Bumper to the Front Profile A RX Compartment to...
cults3d
It also base on the "Raging droner RD5 rear led sma" from "calefpv" https://www.thingiverse.com/thing:3688516 Over the original design I have add a Bumper to the front Profile, A RX compartment to the Back Profile and the Rear Profile support a...
thingiverse
The newly purchased bumpers from Catalyst Machineworks provide a snug and secure fit, unlike their predecessors.
thingiverse
The front bumper is designed to fit both massive Droner and more massive Droner models. To print it, lay it flat in a slicer and use supports. The clean-up process is relatively easy. The front guard is a simple strip that needs to be super-glued...
thingiverse
Canopy for Catalyst Machineworks Merica. Canopy is engineered for: -Matek F722 -TBS Pro32 Nano (+Small Heatsink) -Frsky R9 Mini -Runcam Micro Swift 2 (or comparable) -RealPIT switch -SMA bulkhead connector -AXII antenna (or similar) Position all...
thingiverse
------------------------ Arm Guard for Catalyst Machinworks Raging Droner Designed to be mounted between the arm and the motor, this guard provides essential protection. However, due to my motor screws touching the motor with the standard CM screws,...
thingiverse
... incoming danger. By activating the ultimate protection mode, massive drones can rest assured that their sensitive systems are completely secure from harm, allowing them to maintain their performance and achieve their objectives without interruption.
thingiverse
Install the Catalyst Machineworks Banggod frame which integrates the air unit and antenna spire.
thingiverse
Modular Parts for Catalyst Machineworks BangGod Talystmachine Frame BN-220 Mount TRUE RC Long Airunit Antenna Mount Front Bumper GP Mounts ViFly Mini
thingiverse
Catalyst Machineworks Introduces the Canope MK II, a Revolutionary Upgrade with Enhanced Mobility and Increased Space for Advanced Air Units. ...This Groundbreaking Innovation Is Designed to Provide Unparalleled Versatility and Flexibility on the...
thingiverse
This is a GoPro 7 mount for the Catalyst Machineworks Superlight. This is designed to mount directly on top of the top plate. ... Printed with TPU at 30% infill for best results.
thingiverse
... Matek GPS. The standoff height will be 22 mm, with an offset of 27 mm. The diameter of this component will be 5 mm. To access the full model, click on the following link: https://cults3d.com/en/3d-model/game/catalyst-machineworks-pigtail-gps-matek
cults3d
Catalyst machineworks are seeking a crucial installation. A soft mount is required for the pigtail and Matek GPS assembly. The standoff height must be precisely set at 22 millimeters, while an offset of 27 millimeters is also necessary. ...The diameter...
thingiverse
The following components comprise the Catalyst Machineworks Slamnasty 3" Racer: * Protective arm covers are included * Motor wire protection is also part of this assembly * A cam mounting point is integrated into its design * The micro AXII mount is...
thingiverse
Simple skid for the Catalyst Machineworks Shocker 5". I printed in ABS, but I'm sure you can get away with TPU or PLA just fine. ... This is a Remix from mjameskeogh's Tank deisgn @ https://www.thingiverse.com/thing:4702501
thingiverse
... which causes the frame to appear in the video. ... To fix this issue, try using the mount from the massive droner parts file. This 3D printed item was created with Tinkercad. ...You can edit it online at https://www.tinkercad.com/things/2HkqUyCfOQ8